Question

A simply supported beam of 6m length carries a dead load of 10 kn/m and live...

A simply supported beam of 6m length carries a dead load of 10 kn/m and live load of 8 kn/m. It also support a point dead load of 60Kn at the centre. Using the formula calculate the moment modification factor.

Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A 5.3m long simply supported beam is subjected to a dead load of 23 and live...
A 5.3m long simply supported beam is subjected to a dead load of 23 and live load of 28 kN/m. If the beam has width, height and concrete cover of 25cm, 50cm and 3cm respectively, design this beam. Use C25 and S220. (if required; k1=0.85 and d’’=2cm)
A simply supported beam spans 30 ft. and carries a uniformly distributed dead load of 3.5...
A simply supported beam spans 30 ft. and carries a uniformly distributed dead load of 3.5 kip/ft,excluding the beam self-weight. Also, in addition, a concentrated dead load of 15 kips and a concentrated live load of 25kips, both act at the center of a 30 ft span.Select the lightest-weight W-Shape to carry the load(A992 steel). Use LRFD method.
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6...
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6 kN/m throughout its span and a concentrated load of 15 kN at a point 2 m from the left support. Assuming that the beam has a rectangular shape whose width and depth are 150 mm and 250 mm, respectively. Determine the maximum flexural stress in MPa developed in the beam.
Calculate the bending capacity of a simply supported concrete beam. Beam is 6m long and supporting...
Calculate the bending capacity of a simply supported concrete beam. Beam is 6m long and supporting dead load of 20KN/m and live load of 10KN/m. Compressive strength of the concrete is 25MPa and yield strength of rebars is 500MPa. Concrete beam is 300mm height 200mm width.
A simply supported beam spans 20 ft and carries a uniformly distributed dead load of 0.8...
A simply supported beam spans 20 ft and carries a uniformly distributed dead load of 0.8 kips/ft including the beam self-weight and a live load of 2.3 kips/ft. Determine the required plastic section modulus and select the lightest weight Wshape to carry the moment. Consider only the limit state of yielding (Zone 1) and use A992 steel. Design by (a) LRFD and (b) ASD.
overhanging beam is simply supported at san of 13m and carries of point load of 4000N...
overhanging beam is simply supported at san of 13m and carries of point load of 4000N 3m from right support the left overhangs is 3 m away from left support and has a point load of 5000N. the right overhang is of 4m carrying UDL of 200N per meter for entire rightover . draw shear force and bending moment diagram . calculate the maximum bending moment.
Plot the shear force and bending moment digrams for an 8m long beam simply supported at...
Plot the shear force and bending moment digrams for an 8m long beam simply supported at 0m and 6m. There is a distributed load of 10 KN/m between the two supports and there is a point load of 20kN located at the end of the beam.
A rectangular RC beam is simply supported over a span of 8m and carries a dead...
A rectangular RC beam is simply supported over a span of 8m and carries a dead load of 15kN/m (including self-weight) and an imposed load of 8kN/m. The beam is 250mm wide and has an effective depth of 400mm. Grade 30 concrete is to be used. Determine if the beam should be singly reinforced or doubly reinforced.
Design the shown beam; if it is given that Dead load, wd = 15 kN/m Live...
Design the shown beam; if it is given that Dead load, wd = 15 kN/m Live load,   wL = 10 kN/m Beam breadth b = 300 mm   Beam height, h = ℓ/21 mm     where; Span, ℓ = 9;  and S is the student serial number according to the following table. Use; fc = 35 Mpa and fy = 420 Mpa.
A simply supported rectangular beam of 5m span carries a characteristic dead, gk (inclusive of the...
A simply supported rectangular beam of 5m span carries a characteristic dead, gk (inclusive of the beam’s self-weight) and imposed, qk, loads of 15 and 7 kN/m respectively. Given the following data: Beam: 285mm wide and 500mm high, Reinforcement steel: High tensile steel, Concrete grade: C30, Exposure condition: Mild and Fire resistance = 1.5h. Design the rectangular beam according to BS8110.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT