Question

A rectangular RC beam is simply supported over a span of 8m and carries a dead...

A rectangular RC beam is simply supported over a span of 8m and carries a dead load of 15kN/m (including self-weight) and an imposed load of 8kN/m. The beam is 250mm wide and has an effective depth of 400mm. Grade 30 concrete is to be used.

Determine if the beam should be singly reinforced or doubly reinforced.

Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A simply supported rectangular concrete beam is 18 in. wide and has an effective depth of...
A simply supported rectangular concrete beam is 18 in. wide and has an effective depth of 32 in. The beam supports a factored load (wu) of 15 kips/ft. on a clear span of 22 ft. The given load includes the weight of the beam. Use f'c = 4,000 psi. and fy = 60,000 psi. Over what length of span are stirrups required? Group of answer choices 8.35 ft. 9.18 ft. 10.26 ft. Stirrups are not required for this beam. None...
A simply supported rectangular concrete beam is 18 in. wide and has an effective depth of...
A simply supported rectangular concrete beam is 18 in. wide and has an effective depth of 32 in. The beam supports a factored load (wu) of 15 kips/ft. on a clear span of 22 ft. The given load includes the weight of the beam. Use f'c = 4,000 psi. and fy = 60,000 psi. What is the un-rounded stirrup spacing requirement at the critical section? Group of answer choices 3.23 in. 3.63 in. 4.04 in. 4.50 in. None of the...
A simply supported beam spans 20 ft and carries a uniformly distributed dead load of 0.8...
A simply supported beam spans 20 ft and carries a uniformly distributed dead load of 0.8 kips/ft including the beam self-weight and a live load of 2.3 kips/ft. Determine the required plastic section modulus and select the lightest weight Wshape to carry the moment. Consider only the limit state of yielding (Zone 1) and use A992 steel. Design by (a) LRFD and (b) ASD.
A simply supported beam spans 30 ft. and carries a uniformly distributed dead load of 3.5...
A simply supported beam spans 30 ft. and carries a uniformly distributed dead load of 3.5 kip/ft,excluding the beam self-weight. Also, in addition, a concentrated dead load of 15 kips and a concentrated live load of 25kips, both act at the center of a 30 ft span.Select the lightest-weight W-Shape to carry the load(A992 steel). Use LRFD method.
A rectangular, tension-reinforced beam is to be designed for dead load of 500 lb/ft plus self-weight...
A rectangular, tension-reinforced beam is to be designed for dead load of 500 lb/ft plus self-weight and service live load of 1200 lb/ft, with a 22 ft simple span. Material strengths will be fy = 60 ksi and fc・= 3 ksi for steel and concrete, respectively. The total beam depth must not exceed 16 in. Calculate the required beam width and tensile steel requirement, using a reinforcement ratio of 0.60 ρ0.005 . Use ACI load factors and strength reduction factors....
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6...
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6 kN/m throughout its span and a concentrated load of 15 kN at a point 2 m from the left support. Assuming that the beam has a rectangular shape whose width and depth are 150 mm and 250 mm, respectively. Determine the maximum flexural stress in MPa developed in the beam.
A simply supported beam of 6m length carries a dead load of 10 kn/m and live...
A simply supported beam of 6m length carries a dead load of 10 kn/m and live load of 8 kn/m. It also support a point dead load of 60Kn at the centre. Using the formula calculate the moment modification factor.
. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.
A 5.3m long simply supported beam is subjected to a dead load of 23 and live...
A 5.3m long simply supported beam is subjected to a dead load of 23 and live load of 28 kN/m. If the beam has width, height and concrete cover of 25cm, 50cm and 3cm respectively, design this beam. Use C25 and S220. (if required; k1=0.85 and d’’=2cm)
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT