Question

A simply supported beam spans 30 ft. and carries a uniformly distributed dead load of 3.5...

A simply supported beam spans 30 ft. and carries a uniformly distributed dead load of 3.5 kip/ft,excluding the beam self-weight. Also, in addition, a concentrated dead load of 15 kips and a concentrated live load of 25kips, both act at the center of a 30 ft span.Select the lightest-weight W-Shape to carry the load(A992 steel). Use LRFD method.

Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Please give thumbs up

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A simply supported beam spans 20 ft and carries a uniformly distributed dead load of 0.8...
A simply supported beam spans 20 ft and carries a uniformly distributed dead load of 0.8 kips/ft including the beam self-weight and a live load of 2.3 kips/ft. Determine the required plastic section modulus and select the lightest weight Wshape to carry the moment. Consider only the limit state of yielding (Zone 1) and use A992 steel. Design by (a) LRFD and (b) ASD.
A simply supported beam spans 20 ft. and carries a uniformly distributed load of 1 kip/ft,including...
A simply supported beam spans 20 ft. and carries a uniformly distributed load of 1 kip/ft,including the beam self-weight, and a live load of 2.5kip/ft. Determine the minimum required plastic section modulus and select the lightest-weight W-Shape to carry the moment (A992 Steel). Use LRFD method.
design for flexure a beam 12 ft in length,ot a992 steel, with a uniformly distributed live...
design for flexure a beam 12 ft in length,ot a992 steel, with a uniformly distributed live load of 1 kip/ft, and a concentrated dead load of 8.4 kips a distance of 5 ft from one end
Select the lighest W section to carry a uniformly distributed load of 0.2 kip/ft superimposed (i.e....
Select the lighest W section to carry a uniformly distributed load of 0.2 kip/ft superimposed (i.e. in addition to the beam weight) and 0.8 kip/ft live load. The simly supported span is 20' and the compression flange is fully supported against lateral movement. Use LRFD and select for the following steels: A36, A992, and A572 Gr. 65
design a simply supported floor beam of A992 steel to carry a De0ad load of 0.5k/ft...
design a simply supported floor beam of A992 steel to carry a De0ad load of 0.5k/ft and a Live load of 1.5k/ft over a span 24 ft. The beam has Full lateral bracing provided. Show All steps.
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6...
A simply supported beam is 3 m long. It carries a uniformly distributed load of 6 kN/m throughout its span and a concentrated load of 15 kN at a point 2 m from the left support. Assuming that the beam has a rectangular shape whose width and depth are 150 mm and 250 mm, respectively. Determine the maximum flexural stress in MPa developed in the beam.
A 14ft pin-ended column in a braced frame must carry a compressive dead load of 65...
A 14ft pin-ended column in a braced frame must carry a compressive dead load of 65 kips and live load of 130 kips, along with a uniformly distributed transverse dead load of 0.5 kips/ft and live load of 2.5 kips/ft. Will a W12x58, ASTM A992 member be adequate if the transverse load is applied to put bending about the strong-axis? LRFD.
A rectangular RC beam is simply supported over a span of 8m and carries a dead...
A rectangular RC beam is simply supported over a span of 8m and carries a dead load of 15kN/m (including self-weight) and an imposed load of 8kN/m. The beam is 250mm wide and has an effective depth of 400mm. Grade 30 concrete is to be used. Determine if the beam should be singly reinforced or doubly reinforced.
A simply supported beam of 6m length carries a dead load of 10 kn/m and live...
A simply supported beam of 6m length carries a dead load of 10 kn/m and live load of 8 kn/m. It also support a point dead load of 60Kn at the centre. Using the formula calculate the moment modification factor.
Design an all-bolted double-angle connection for a W18×65 A992 beam to carry a dead load reaction...
Design an all-bolted double-angle connection for a W18×65 A992 beam to carry a dead load reaction of 15 kips and a live load reaction of 45 kips. Use 5/16 in. A36 angles and 3/4 in. A325-N bolts in standard holes. The uncoped beam is connected to the flange of a W14×109 A992 column. Design by LRFD.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT