Question

Calculate the bending capacity of a simply supported concrete beam. Beam is 6m long and supporting...

Calculate the bending capacity of a simply supported concrete beam.

Beam is 6m long and supporting dead load of 20KN/m and live load of 10KN/m. Compressive strength of the concrete is 25MPa and yield strength of rebars is 500MPa.

Concrete beam is 300mm height 200mm width.

Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A 5.3m long simply supported beam is subjected to a dead load of 23 and live...
A 5.3m long simply supported beam is subjected to a dead load of 23 and live load of 28 kN/m. If the beam has width, height and concrete cover of 25cm, 50cm and 3cm respectively, design this beam. Use C25 and S220. (if required; k1=0.85 and d’’=2cm)
A simply supported beam of 6m length carries a dead load of 10 kn/m and live...
A simply supported beam of 6m length carries a dead load of 10 kn/m and live load of 8 kn/m. It also support a point dead load of 60Kn at the centre. Using the formula calculate the moment modification factor.
Plot the shear force and bending moment digrams for an 8m long beam simply supported at...
Plot the shear force and bending moment digrams for an 8m long beam simply supported at 0m and 6m. There is a distributed load of 10 KN/m between the two supports and there is a point load of 20kN located at the end of the beam.
. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The...
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The beam spans 12.0 m and is subject to a superimposed dead load of 50 kN/m and a live load of 35 kN/m. Both the superimposed dead load and live load are applied after transfer (after stressing has taken place). The tendon is located at the mid-height of the beam at each end, and its centreline sits 50 mm from the base at midspan. The...
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian.
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m...
2. A simply supported beam has a width of 200mm and depth of 400mm is 4m long. It carries a uniformly distributed load of 20 kN/m over the whole beam and a point load of 40 kN at the center of the beam. Compute the maximum deflection if the maximum slope produced in the beam is 2× ??-3 radian. (6 M Blease i want prompt clear solution for this question in detail,.
A simply supported reinforced-concrete beam has to resist a maximum factored moment of M* = 210...
A simply supported reinforced-concrete beam has to resist a maximum factored moment of M* = 210 KN-m. Given that f’c = 32 MPa, fy = 500 MPa and that the maximum possible width for the beam is 240 mm: a. Establish an appropriate structural depth ‘d’ for the beam b. Determine the total depth ‘D’ of the beam for a FRL of 90 minutes c. Find the area of steel Ast required to resist the moment and select the rebars....
A rectangular RC beam is simply supported over a span of 8m and carries a dead...
A rectangular RC beam is simply supported over a span of 8m and carries a dead load of 15kN/m (including self-weight) and an imposed load of 8kN/m. The beam is 250mm wide and has an effective depth of 400mm. Grade 30 concrete is to be used. Determine if the beam should be singly reinforced or doubly reinforced.
The project will include the design of One Way Slabs, Beams and Columns. Choose the largest...
The project will include the design of One Way Slabs, Beams and Columns. Choose the largest room in your house/apartment and measure the area. let's say (length 6m* width 4m) ( height 3m) Steel yield stress (fy = 60000 psi) Concrete ultimate compressive strength (f’c = 4000 psi) Reinforced concrete density = 150 lb/ft3. Normal weight concrete is used. The slab is treated as a one way slab and subjected to a dead load of 120 psf (excluding the self-weight...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT