Question

Please create examples of both D-Latch and D-Flip-Flop circuits using an online circuit simulator.

Please create examples of both D-Latch and D-Flip-Flop circuits using an online circuit simulator.

Engineering   Computer-Science   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

here the difference between teh latch and flip flop is clock.In d latch we use enable pin to activate the circuit.

Here I implemented the 2 bit counter using D-latch and D -Flip flop.

2 bit counter means it generates 0,1 this is the best example circuit for both D-ff and D-latch

When D-latch En pin is then the D-latch is deactive state

in the above diagram En =1 means it is in activate state it is 2 bit counter so first it generates output 0.

In the below circuit it generate output 1.

Now same operation using D-ff:-

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
- Examine the operation of the RS latch - Examine the operation of the D flip-flop...
- Examine the operation of the RS latch - Examine the operation of the D flip-flop - Examine the operation of the JK flip-flop Please no handwritten answers
Implement the following circuit to test the characteristics of a D flip flop. Note: Using a...
Implement the following circuit to test the characteristics of a D flip flop. Note: Using a clock input to operate the flip-flop is rather quickly. You may wish to select the slow motion of the clock OR to use a simple binary input device instead of a clock input device. Verify the flip flop state table. Q(t+1) = D, is the characteristic equation. Characteristic Table Excitation Table ==================== =================== D Q(t+1) Operation Q(t) Q(t+1) D ==================== =================== 0 0 Reset...
Implement the following circuit to test the characteristics of a D flip flop. Note: Using a...
Implement the following circuit to test the characteristics of a D flip flop. Note: Using a clock input to operate the flip-flop is rather quickly. You may wish to select the slow motion of the clock OR to use a simple binary input device instead of a clock input device. Verify the flip flop state table. Q(t+1) = D, is the characteristic equation. Characteristic Table Excitation Table ==================== =================== D Q(t+1) Operation Q(t) Q(t+1) D ==================== =================== 0 0 Reset...
1) Write down the characteristic table for a positive-edge triggered D flip-flop. 2) Explain the difference...
1) Write down the characteristic table for a positive-edge triggered D flip-flop. 2) Explain the difference between the D latch and the D flip-flop.
Please no handwriting Start a new Quartus project for J-K flip-flop active low type the VHDL...
Please no handwriting Start a new Quartus project for J-K flip-flop active low type the VHDL code create the circuits in Quartus.
Using one SR one JK and one D flip flop design a sequential circuit that generates...
Using one SR one JK and one D flip flop design a sequential circuit that generates the output pattern: 7-6-5-4-3-2-1-0 and then the sequence repeats. Derive the equations for SA, RA, JB, KB, and DC.
Simulate a D-Flip Flop on Xilinx using Verilog HDL | Behavioral Modelling
Simulate a D-Flip Flop on Xilinx using Verilog HDL | Behavioral Modelling
As an alternative to using a SPDT switch and an RS latch to debounce a switch...
As an alternative to using a SPDT switch and an RS latch to debounce a switch signal, would passing the bouncing signal thru a D flip-flop remove bounces? What constraint might you place on a D type flip-flop’s clock to mitigate the possibility of passing a bounce thru? (Consider your past experience with bouncing switches).
How do I design a divide by 4 clock in verilog using 2 D Flip Flop...
How do I design a divide by 4 clock in verilog using 2 D Flip Flop blocks? I have created this divide by 2 clock D Flip Flop block so far: module divide_by_2(D, Clk,reset, Q, Qnext); //Divide by 2 clock with reset using D flip flop    input Clk, D, reset;    output Q,Qnext;    reg Q;       assign Qnext = ~Q;       always @(posedge Clk or posedge reset) //always at the positive edge of the clock or...
Question 1:A) A sequential circuit has two flip-flops A and B, two inputs X and Y,...
Question 1:A) A sequential circuit has two flip-flops A and B, two inputs X and Y, and one output Z. The flip-flop input equations and output function are as follows: SA = BX + B’Y’ RA = B’XY’ SB = A’X RB = A + XY’ Z = AXY+BX’Y’ a) Draw the logic diagram of the circuit. b) Derive the state table and state diagram of the circuit. Question 1: b)For the sequential circuits given below a) Write flip-flop input...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT