Question

PRESTRESSED CONCRETE. If the capacity of the section proves to be lower than the required strength...

PRESTRESSED CONCRETE. If the capacity of the section proves to be lower than the required strength of the member, what are the possible ways of increasing the capacity of the member to make it adequate.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A new concrete mix is being designed to provide adequate compressive strength for concrete blocks. The...
A new concrete mix is being designed to provide adequate compressive strength for concrete blocks. The specification for a particular application calls for the blocks to have a mean compressive strength µ greater than 1350 kPa. A sample of 100 blocks is produced and tested. Their mean compressive strength is 1356 kPa and their standard deviation is 70 kPa. What is the most appropriate null hypothesis regarding the population mean µ. Indicate the alternate hypothesis as well. Find the P-value....
Correct the following sentence as required: There is many ways to reinforce a concrete shearwall, but...
Correct the following sentence as required: There is many ways to reinforce a concrete shearwall, but they all should include meeting the requirements of ACI 318, and providing adequate amounts of reinforcing to resist apply moments and shears due to wind loads and gravity loads.
A reinforced concrete beam is constructed with Grade 30 concrete which has a cross section of...
A reinforced concrete beam is constructed with Grade 30 concrete which has a cross section of 450 mm x 660 mm (b = 450 mm and D = 660 mm). The length of the beam is 5 m. The elastic modulus of the concrete is 32.8 GPa. A uniformly distributed live load of 23 kN/m is acting on the beam. Determine (a) the design bending moment on this beam for strength limit state, (b) modular ratio assuming Es = 200...
The data in the Excel sheet labeled 'Concrete' represent the compressive ​strength, in thousands of pounds...
The data in the Excel sheet labeled 'Concrete' represent the compressive ​strength, in thousands of pounds per square inch​ (psi), of 20 samples of concrete taken two and seven days after pouring. At the 0.01 level of​ significance, is there evidence that the mean strength is lower at two days than at seven​ days? What test will you use? What is the p-value? Reject Ho? Is there evidence of a lower strength? Two days Seven days Sample 1 3.8 4.07...
From a field data,       Required compressive strength of an OPC air entrained concrete column at...
From a field data,       Required compressive strength of an OPC air entrained concrete column at a moderate exposure is 37±3 MPa. Determine the amount of the ingredients in kg, per 1m3 of concrete: (a) water (b) cement (c) percent air content (d) coarse aggregate (No need to adjust moisture for coarse aggregate):         Given, Nominal maximum size of coarse aggregate is 25 mm Bulk OD specific gravity of coarse aggregate is 2.64 Oven dry-rodded density: 1650 kg/m3 Fineness modulus...
As concrete​ cures, it gains strength. The following data represent the​ 7-day and​ 28-day strength in...
As concrete​ cures, it gains strength. The following data represent the​ 7-day and​ 28-day strength in pounds per square inch​ (psi) of a certain type of concrete. Complete parts​ (a) through​ (f) below. ​7-Day Strength​ (psi), x 24802480 33903390 23002300 33803380 26202620 Open in StatCrunch + Copy to Clipboard + Open in Excel + ​28-Day Strength​ (psi), y 41204120 52205220 40704070 50205020 41904190 ​(a) Treating the​ 7-day strength as the explanatory​ variable, x, use technology to determine the estimates of...
The accompanying data is on cube compressive strength (MPa) of concrete specimens. 112.5      97.0     ...
The accompanying data is on cube compressive strength (MPa) of concrete specimens. 112.5      97.0      92.6      86.0      102.0 99.1      95.8      103.5      89.0      86.6 (a) Is it plausible that the compressive strength for this type of concrete is normally distributed? The normal probability plot is not acceptably linear, suggesting that a normal population distribution is plausible. The normal probability plot is acceptably linear, suggesting that a normal population distribution is plausible.     The normal probability...
A design engineering determined a water-cement ratio of 0.45 based on the required strength of 4200...
A design engineering determined a water-cement ratio of 0.45 based on the required strength of 4200 psi for concrete. However, the engineering was told that the concrete will subjected to chloride, salt water, brackish water. etc. What is the water-cement ratio to be used for the concrete mix?
Timber has much lower values of allowable bending and shear stress than either reinforced concrete or...
Timber has much lower values of allowable bending and shear stress than either reinforced concrete or structural steelwork. What situations might give rise to a situation when timber is the preferred structural material for a structure? Include examples.
a rectangular beam having dimensions: b=300mm and d=550mm, spans 6m face to face of simple supports....
a rectangular beam having dimensions: b=300mm and d=550mm, spans 6m face to face of simple supports. it is reinforced for flexure with 3D36mm bars that continue uninterrupted to the ends of the soan. it is to carry a service dead load of 23.8 KN/m (including self-weight) and a service lice load equal to 47.6 KN/m, both uniformly distributed along the span. use fc’=27.6 Mpa and fy=414.7 Mpa. Normal weight concrete will be used and diameter of stirrup are 10mm. 1.using...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT