Question

Design an op-amp circuit that will provide an output voltage equal to the average of three...

Design an op-amp circuit that will provide an output voltage equal to the average of three input voltages. You may assume that the input voltages will be confined to the range -10V ?Vin ?10V. Verify your design by using Multisim software and a suitable set of input voltages.

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
4. Using an op amp, design a circuit to produce an output voltage related to two...
4. Using an op amp, design a circuit to produce an output voltage related to two input voltages by the equation ?? = 1 2 ?2 − ?? (Use the feedback resistance R2 = 10kΩ). Devise a procedure to verify your design.
Design an Op-Amp phase shift circuit that must accept a sine waveform voltage at its input...
Design an Op-Amp phase shift circuit that must accept a sine waveform voltage at its input ??? (?) = 10 sin (120??) mV, and must provide at its output, an output voltage of 1.2 Vrms and with an offset of −120 ° with respect to the input signal.
Using a 741 op-amp for every stage, design this circuit: The input stage has a voltage...
Using a 741 op-amp for every stage, design this circuit: The input stage has a voltage gain of 10 and input impedance of 50 K?. The low pass filter stage has a Sallen-Key (VCVS) third order butterworth response and a cutoff frequency of 5KHz. The output buffer stage has a voltage gain of 10.
Design an Op-Amp Circuit that takes an input from a low current capacity voltage source (i.e....
Design an Op-Amp Circuit that takes an input from a low current capacity voltage source (i.e. a high internal impedance source) with voltage range of -15mV to 15mV, amplify it, adds a DC offset so that the voltage is always positive filter it (LPF 1, 18.3 KHz) and the convert it into digital output (reference voltage of ADC 12V). Also determine the minimum sampling rate of ADC
Design an op-amp circuit for a weighted summer that shifts the dc level of the input...
Design an op-amp circuit for a weighted summer that shifts the dc level of the input signal vi(t) = 3 sin(t) V from zero to -3 V. Assume that in addition to vi(t), you have a dc voltage source of 1.5 V available. Sketch the output signal waveform.
The input, Vin, is single-ended not differential. Design an analog circuit with a transfer function of...
The input, Vin, is single-ended not differential. Design an analog circuit with a transfer function of Vout = 50 ⋅ Vin − 5 using one rail-to-rail op amp powered by a single +5 V supply. You may use one REF03 2.50 V reference chip. The input range is 0.1 to 0.2 V, and the output range is 0 to +5 V.
Deisgn an op-amp circuit that will give you an output voltage from 5V to 0V. There...
Deisgn an op-amp circuit that will give you an output voltage from 5V to 0V. There must be a resistor where when the resistance is 3475 voltage is 5v and when the resitance is 10,000 the output votlage must be zero.
Design a multi-stage op-amp network that takes an input signal of vin(t) = 5 cos(120πt) V...
Design a multi-stage op-amp network that takes an input signal of vin(t) = 5 cos(120πt) V and outputs vout(t) = 2.5 + 2.5 sin(120πt) V. All resistors used must have values of at least 1 kΩ. Verify your design behaves as required using LTSpice XVII. (20 points)
If you were to choose an op-amp to implement an amplifier circuit for picking up ECG...
If you were to choose an op-amp to implement an amplifier circuit for picking up ECG (electrocardiographic) pulses from adhesive electrodes, which type of op-amps, instrumentation (INA121, AD620 etc), FET-input (AD547, OPA128 etc) or BJT-input (uA741, OP27 etc), should you choose? Perform an internet search on the data-sheet of these op-amps. Compare their performance characteristics. Provide THREE justifications to support your decision.
Use an ideal op amp to design a differentiator circuit having a time constant of 10-5s...
Use an ideal op amp to design a differentiator circuit having a time constant of 10-5s using a 1-nF capacitor. Sketch the magnitude and phase response of the circuit, indicating the frequency at which the magnitude response equals 0 dB. A series input resistor is added to limit the gain magnitude at high frequencies to 100 V/V. Sketch the magnitude and phase responses of this modified circuit on the same axes as the ideal differentiator. How does the phase response...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT