Question

Design an Op-Amp phase shift circuit that must accept a sine waveform voltage at its input...

Design an Op-Amp phase shift circuit that must accept a sine waveform voltage at its input ??? (?) = 10 sin (120??) mV, and must provide at its output, an output voltage of 1.2 Vrms and with an offset of −120 ° with respect to the input signal.

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design an op-amp circuit for a weighted summer that shifts the dc level of the input...
Design an op-amp circuit for a weighted summer that shifts the dc level of the input signal vi(t) = 3 sin(t) V from zero to -3 V. Assume that in addition to vi(t), you have a dc voltage source of 1.5 V available. Sketch the output signal waveform.
Design an Op-Amp Circuit that takes an input from a low current capacity voltage source (i.e....
Design an Op-Amp Circuit that takes an input from a low current capacity voltage source (i.e. a high internal impedance source) with voltage range of -15mV to 15mV, amplify it, adds a DC offset so that the voltage is always positive filter it (LPF 1, 18.3 KHz) and the convert it into digital output (reference voltage of ADC 12V). Also determine the minimum sampling rate of ADC
Design an op-amp circuit that will provide an output voltage equal to the average of three...
Design an op-amp circuit that will provide an output voltage equal to the average of three input voltages. You may assume that the input voltages will be confined to the range -10V ?Vin ?10V. Verify your design by using Multisim software and a suitable set of input voltages.
Using a 741 op-amp for every stage, design this circuit: The input stage has a voltage...
Using a 741 op-amp for every stage, design this circuit: The input stage has a voltage gain of 10 and input impedance of 50 K?. The low pass filter stage has a Sallen-Key (VCVS) third order butterworth response and a cutoff frequency of 5KHz. The output buffer stage has a voltage gain of 10.
4. Using an op amp, design a circuit to produce an output voltage related to two...
4. Using an op amp, design a circuit to produce an output voltage related to two input voltages by the equation ?? = 1 2 ?2 − ?? (Use the feedback resistance R2 = 10kΩ). Devise a procedure to verify your design.
Use an ideal op amp to design a differentiator circuit having a time constant of 10-5s...
Use an ideal op amp to design a differentiator circuit having a time constant of 10-5s using a 1-nF capacitor. Sketch the magnitude and phase response of the circuit, indicating the frequency at which the magnitude response equals 0 dB. A series input resistor is added to limit the gain magnitude at high frequencies to 100 V/V. Sketch the magnitude and phase responses of this modified circuit on the same axes as the ideal differentiator. How does the phase response...
Design a multi-stage op-amp network that takes an input signal of vin(t) = 5 cos(120πt) V...
Design a multi-stage op-amp network that takes an input signal of vin(t) = 5 cos(120πt) V and outputs vout(t) = 2.5 + 2.5 sin(120πt) V. All resistors used must have values of at least 1 kΩ. Verify your design behaves as required using LTSpice XVII. (20 points)
Consider an op-amp connected in an inverting configuration to realize a closed-loop gain of -100 V/V...
Consider an op-amp connected in an inverting configuration to realize a closed-loop gain of -100 V/V utilizing resistors of 1k and 100 k. A load resistance RLis connected from the output to ground, and a low-frequency sine-wave signal of peak amplitude Vpeakis applied to the input. Let the op amp be ideal except that its output voltage saturates at 10 Vand its output current is limited to the range of 20 mA. 1) For RL = 1k, what is the...
A single phase AC induction motor need to be controlled by varying its input frequency. The...
A single phase AC induction motor need to be controlled by varying its input frequency. The supply frequency is a single phase with 50 Hz and the input frequency to the motor is controlled to be 12.5 Hz. Design a Full-wave rectifier (Cycloconverter), show the conversion of 5 cycles, and explain its operation. And show how the output voltage of Cycloconverters can be controlled to get a waveform shape near sine wave.
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS)...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. 2. The voltage Vcc will be +8 vDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn. 3. Simulate the circuit in LTSpice. It must choose resistors Ro, Rs, RG1 and RG2 such that the circuit operates...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT