Question

The specific heat of a certain solid follows the equation Cp = bT³ between 0 and...

The specific heat of a certain solid follows the equation Cp = bT³ between 0 and 250 K. Since b = 3.5J / K³, determine the entropy of this solid at 50 K according to the third law (in kJ / K)

Homework Answers

Answer #1

In case of any doubt please comment below.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. The specific heat of iron metal is 0.450 J/g⋅K. How many J of heat are...
1. The specific heat of iron metal is 0.450 J/g⋅K. How many J of heat are necessary to raise the temperature of a 1.05 −kg block of iron from 28.0 ∘Cto 85.0 ∘C? 2. A 1.80-g sample of phenol (C6H5OH) was burned in a bomb calorimeter whose total heat capacity is 11.66 kJ/∘C. The temperature of the calorimeter plus contents increased from 21.36∘Cto 26.37∘C. A. Write a balanced chemical equation for the bomb calorimeter reaction. B. What is the heat...
Consider a cube of density, specific heat, and thermal conductivity of 2700 kg/m3, 0.896 kJ/kg-K, and...
Consider a cube of density, specific heat, and thermal conductivity of 2700 kg/m3, 0.896 kJ/kg-K, and 204 W/m-K, respectively. The cube is 5 cm in length, and is initially at a temperature of 20 oC. For t>0, two of the boundary surfaces are insulated, two are subjected to uniform heating at a rate of 10,000 W/m2, and two dissipate heat by convection to an ambient temperature of 20 oC, with a heat transfer coefficient of 50 W/m2-K. Assuming lumped capacitance...
A 2.0 mol sample of ideal gas with molar specific heat Cv = (5/2)R is initially...
A 2.0 mol sample of ideal gas with molar specific heat Cv = (5/2)R is initially at 300 K and 100 kPa pressure. Determine the final temperature and the work done on the gas when 1.6 kJ of heat is added to the gas during each of these separate processes (all starting at same initial temperature and pressure: (a) isothermal (constant temperature) process, (b) isometric (constant volume) process, and (c) isobaric (constant pressure) process. Hint: You’ll need the 1st Law...
A student collected the following data to determine the specific heat of a metal sample.  50.0 g...
A student collected the following data to determine the specific heat of a metal sample.  50.0 g of metal were transferred from boiling water into a calorimeter containing 100 g of H2O at 22.3oC.  The temperature of the water rose to 23.5oC.  Calculate the specific heat of the metal. Enter your answer with 3 significant figures. Based on the calculated specific heat, what is the most likely identity of the metal in the previous problem? Give your answer as the elemental symbol (e.g....
1. The equation Δ?=?0?+0.5??2Δx=v0t+0.5at2 Can be used to describe an object's position x. When can this...
1. The equation Δ?=?0?+0.5??2Δx=v0t+0.5at2 Can be used to describe an object's position x. When can this equation be applied? Group of answer choices: A. Displacement must be constant B. The object must be acted on by no more than one force C. Velocity must be constant D. Acceleration must be constant E. The force acting on the object must be gravity 2. If a vector A has a y component equal to |?|cos?|A|cos⁡θ, then the angle ?θ is the angle...
Learning Goal: To understand reaction order and rate constants. For the general equation aA+bB?cC+dD, the rate...
Learning Goal: To understand reaction order and rate constants. For the general equation aA+bB?cC+dD, the rate law is expressed as follows: rate=k[A]m[B]n where m and n indicate the order of the reaction with respect to each reactant and must be determined experimentally and k is the rate constant, which is specific to each reaction. Order For a particular reaction, aA+bB+cC?dD, the rate law was experimentally determined to be rate=k[A]0[B]1[C]2=k[B][C]2 This equation is zero order with respect to A. Therefore, changing...
1. An oven chimney is made of brick with a heat transmission coefficient 1.1 W/mK 10...
1. An oven chimney is made of brick with a heat transmission coefficient 1.1 W/mK 10 cm thick. Since the shaft exterior radiation beam coefficient is 0.8 and the flue gas temperature is 350°C, the external ambient temperature is 25°C and the outer ambient heat transport coefficient is 20 W/m2K; a) Calculate the shaft exterior temperature. b) In order to reduce the risk of burn injury that may occur in the body, the shaft is asked to be below 55°Cve...
Heat is the Total internal energy of an object Average kinetic energy of molecules Measure of...
Heat is the Total internal energy of an object Average kinetic energy of molecules Measure of potential energy of molecules Same thing as very high temperature The specific heat of copper is 0.093 cal/g⁰C, and the specific heat of aluminum is 0.22  cal/g⁰C. The same amount of energy applied to equal masses, say, 50 g of copper and aluminum, will result in A higher temperature for copper A higher temperature for aluminum The same temperature for each metal Unknown results The...
What are standard conditions of ΔH° for the data you will use? Temperature 0 K 100...
What are standard conditions of ΔH° for the data you will use? Temperature 0 K 100 K 273 K 298 K Pressure 1.0 Pa 100 Pa 1.0 bar 100 bar Concentration 1.0 g/L 1.0 mol/L 1.0 mg/L mol/kg Select the complete reactions (including phases) for the reaction between solid NaOH and a solution of HCl. 2NaOH(s) + HCl(aq) → 2NaCl(aq) + H2O(l) NaOH(s) + HCl(aq) → NaCl(aq) + H2O(l) NaOH(s) + HCl(aq) → NaCl(s) + H2O(l) Calculate the theoretical ΔH°r...
A shell and-tube heat exchanger is required for the following service: Hot stream Cold Stream Aromatic...
A shell and-tube heat exchanger is required for the following service: Hot stream Cold Stream Aromatic Stream Cooling Water inlet Temperature (oC) 85 20 outlet Temperature (oC) 40 35 Mass Flowrate x heat Capacity (kW/oC) 85.2 Hot Stream cold stream (Cooling water) Heat Capacity (J/kg K) 2840 4193 Density (kg/m3) 750 999 Viscosity (cP) 0.34 1.016 Thermal conductivity (W/m.K) 0.19 0.594 Fouling Factor (m2.oC/W 0.00018 0.000176 ? The cooling water is allocated to the tube-side of the exchanger. ? It...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT