Question
Design a Full Subtractor circuit that takes x, y, bin as inputs and produces bout and...
Design a Full Subtractor circuit that takes x, y, bin as inputs and produces bout and difference(d) at the output
Design a combinational circuit that has 3 inputs and whose output is produced by adding 1 to the input.
Homework Answers
Answer #1
If you have any questions comment down. Please don't simply downvote and leave. If you are satisfied with answer, please? upvote thanks
Not the answer you're looking for?
Similar Questions
Design a combinational circuit with inputs a, b, c, d and outputs w, x, y, z....
Design a combinational circuit with inputs a, b, c, d and
outputs w, x, y, z. Assume that the inputs a, b, c, d represent a
4-bit signed number (2s complement). The output is also a signed
number in 2s complement which is 7 greater than the input if the
input is less than 2, and is 3 less than the input if the input is
greater than or equal to 2.
Design a combinational circuit with 4 inputs (A, B, C, D) and two outputs (F, G):...
Design a combinational circuit with 4 inputs (A, B, C, D) and
two outputs (F, G): The F output becomes ‘1’ when the corresponding
decimal value represented by the 4 input bits is divisible by 3
(for example, F=1 when input combination is 0011; as 0011is 3 in
decimal that is div. by 3). The G output becomes ‘1’ when the
corresponding decimal value represented by the 4 input bits is
divisible by 5.
Also, mention how many gate delays...
Use contraction beginning with a 4-bit adder-subtractor with carry in, to design a 4-bit circuit without...
Use contraction beginning with a 4-bit adder-subtractor with
carry in, to design a 4-bit circuit without carry out that
increments its input by 0010 for input S=0 and decrements its input
by 0010 for input S=1. Perform the design by designing the distinct
1-bit full adder cells needed and indicating the type of cell used
in each of the four bit positions.
Design a 4-bit adder-subtractor circuit using the 4-bit binary Full adders (74LS83) and any necessary additional...
Design a 4-bit adder-subtractor circuit using the 4-bit binary
Full adders (74LS83) and any necessary additional logic gates. The
circuit has a mode input bit, M, that controls its operation.
Specifically, when M=0, the circuit becomes a 4-bit adder, and when
M=1, the circuit becomes a 4-bit subtractor that performs the
operation A plus the 2’s complement of B.Where A and B are two
4-bits binary numbers. That is,
* When M=0, we perform A+B, and we assume that
both...
Design a circuit that takes three bits, X2, X1, X0 as input and produces one output,...
Design a circuit that takes three bits, X2, X1, X0 as input and
produces one output, F. F is 0 if and only if 4<=X<=6 when X
= (X2, X1, X0) is read as an unsigned integer.
X2
X1
Xo
F
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1...
Question 1:A) A sequential circuit has two flip-flops A and B, two inputs X and Y,...
Question 1:A) A sequential circuit has two flip-flops A and B,
two inputs X and Y, and one output Z. The flip-flop input equations
and output function are as follows: SA = BX + B’Y’ RA = B’XY’ SB =
A’X RB = A + XY’ Z = AXY+BX’Y’ a) Draw the logic diagram of the
circuit. b) Derive the state table and state diagram of the
circuit.
Question 1: b)For the sequential circuits given below a) Write
flip-flop input...
Q.1.It is required to design an iterative combinational circuit that computes the equation Z=2*X-3, where X...
Q.1.It is required to design an iterative
combinational circuit that computes the equation Z=2*X-3, where X
is an n-bit signed number in 2’s complement representation. (Hint:
-3 can be represented as -1+-1+-1 in 2’s complement representation,
where -1 is represented as 111…..111).
a)Determine the number of inputs and outputs
needed for your 1-bit cell. Explain the meaning of values in the
interface signals.
b)Derive the truth table of your 1-bit
cell.
c) Derive minimized equations for your 1-bit
using K-Map...
My question: what is the truth table for full-comparator?? Full question: Design a comparator circuit for...
My question: what is the truth table for full-comparator??
Full question: Design a comparator circuit for binary numbers
using only NAND gates. It should take as input two numbers
represented in standard binary, X and Y, and produce two outputs, G
and L, which indicate that X is Greater than or Less than Y,
respectively. If both outputs are zero, it indicates that the
values are equal. Design a half-comparator, full-comparator, and a
full four-bit comparator. With nothing more than...
Task: Design and Build a 3-to-1 MUX–4 Design a circuit that takes three different 4-bit words...
Task: Design and Build a 3-to-1 MUX–4
Design a circuit that takes three different 4-bit words and selects
one to be connected to the output. In your template provide the
design schematic as well as the approach you would use to test the
circuit.
Design a synchronous machine (Transition Table, K-maps, Final Equations, Circuit Diagram) that counts through the following...
Design a synchronous machine (Transition Table, K-maps, Final
Equations, Circuit Diagram) that counts through the following
sequence in the order shown below. Note, there are no inputs or
output variables, so your Q values must reflect the Hex value
listed.
A 4 1 2 6 3 9 C 7 and repeat
a) using D flip-flops and combinational logic
b) using a PROM device (must show Hex values in order) and 4-bit
D-Register
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 1 minute ago
asked 10 minutes ago
asked 16 minutes ago
asked 29 minutes ago
asked 30 minutes ago
asked 32 minutes ago
asked 44 minutes ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago