Question

What values are in the status register after the operation 1000 + 1111 for a 4-bit...

What values are in the status register after the operation 1000 + 1111 for a 4-bit ALU? ("+" means addition)
Z:  
V:  
C:  
N:

Homework Answers

Answer #1

1000 + 1111 = 010111

8 + 15 = 23

Z is zero bit

V is overflow bit

C is carry bit

N is negative bit

Zero bit will be turned on if the output is 0 but output isn't zero so zero register will be turned off 0

Overflow bit will turn on if the set result is greater than 127 and less than -128 in our case it will be 0

Carry bit will turn on because we on the left most bit carry was generated it will be 1

Negative bit will be turn of because the result is positive so it will be 0

So, the values of all status registers are below

Z: 0000

V: 0000

C: 0001

N: 0000:

IF YOU HAVE ANY QUERY PLEASE COMMENT DOWN BELOW
PLEASE GIVE A THUMBS UP

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
The following are the %l2 register values, the %l3 register values, and the commands to execute:...
The following are the %l2 register values, the %l3 register values, and the commands to execute: After executing the command, write the values of the Condition code Z, N, V, C, and %l4 registers in the table. 1) %l2: 0x8000_0000 %l3: 0x8000_0000 addcc %l2, %l3, %l4 -------------------------> Z=? , N=? , V=? , C=? , %l4=? 2) %l2: 0x0123_4567 %l3: 0xFEDC_BA98 xorcc %l2, %l3, %l4 -------------------------> Z=? , N=? , V=? , C=? , %l4=?
Supposetheregisters4and5containthebit patterns 3C and C8, respectively. What bit pattern is left in register 0 after executing...
Supposetheregisters4and5containthebit patterns 3C and C8, respectively. What bit pattern is left in register 0 after executing each of the following instructions: 5045 7045 8045 9045
4-bit register using jk flip flops. 1)What is the purpose of anding the clock signal and...
4-bit register using jk flip flops. 1)What is the purpose of anding the clock signal and the load input together in your circuit? 2) How would I be able to store 1011 into the 4-bit register? Explain the process. For example, what do your inputs should be? Should your clock be on or off? How about your load input? How does your load input work when you want to store bits into your register? 3) If your load input is...
(In c code only, not c++) We will simulate the status of 8 LEDs that are...
(In c code only, not c++) We will simulate the status of 8 LEDs that are connected to a microcontroller. Assume that the state of each LED (ON or OFF) is determined by each of the bits (1 or 0) in an 8-bit register (high-speed memory). Declare a char variable called led_reg and initialize it to 0. Assume that the least-significant bit (lsb) controls LED#0 and the most-significant bit (msb) controls LED#7. In the main function, build and present a...
I. What value will be in register r2 after execution of the following instructions? Show your...
I. What value will be in register r2 after execution of the following instructions? Show your work with the register values after executing each instruction. MOV r2, #0x0 LDR r1, =0xCF MOVS r1, r1, LSR #1 ADC r2, r2, #0 MOVS r1, r1, LSR #1 ADC r2, r2, #0 II. Assume a 32 bit register holds a data of four bytes as B3B2B1B0. Write a sequence of ARM instruction that takes this data as input and swaps the bytes 0...
4)What will be the output when the computer performs arithmetic left shift operation on the bit...
4)What will be the output when the computer performs arithmetic left shift operation on the bit pattern11010101 which is stored in two’s complement format?Verify that if you multiply the original number in decimal by 2 you get your final answer in decimal. Show your work?
4) If variable A=0x05 & register B=0x10, and you compare the variables with the instruction (a>=b),...
4) If variable A=0x05 & register B=0x10, and you compare the variables with the instruction (a>=b), what's the contents of A, B after the comparison: a) 05, 10 b) 15, 05 c) F1, 00 d) F1, 10 e) 15, 00 5) In the instruction above, what's the value of the N, Z conditions after the execution: a) 0,0 b) 1,0 c) 0,1 d) 1,1 e) 0,0 6) If A = 0xAB, and you execute a shift right instruction A=A>, what...
QUESTION 1 During a single clock tick, how many 64-bit values can be written to an...
QUESTION 1 During a single clock tick, how many 64-bit values can be written to an input of a register file with 8 64-bit registers (i.e. an 8x64 register file)? QUESTION 2 Suppose you are designing a processor that contains a register file with 32 32-bit registers (i.e. a 32x32 register file). What is the minimum number of bits required in order to select which register is being written to? QUESTION 3 If the decimal value, 30, is shifted to...
VII. After execution of the following instructions what value will be in register r2? Trace the...
VII. After execution of the following instructions what value will be in register r2? Trace the program and write the value of the registers at each line to receive full credit. LDR r12, =0xA4000000 LDR r0, =0x2D STR r0, [r12, #-4]! LDR r0, =0x5E STR r0, [r12, #-4]! LDR r0, =0xD5 STR r0, [r12, #-4]! LDMIA r12!, {r0-r2} SUB r2, #0x68 VIII. Write a simple ARM assembly program to divide a 32 bit positive number stored in r0 by a...
4. Answer the following questions: (diff=3) a. For n = 4, what are the possible values...
4. Answer the following questions: (diff=3) a. For n = 4, what are the possible values of the angular momentum quantum number, l? b. What subshells are possible within n = 4? c. For l = 2, what are the possible values of the magnetic quantum number, ml? d. What orbitals do these l and ml values correspond to? e. If ml is 2, what are the possible values for l ? f. What is the maximum number of electrons...