Question

Consider water flowing upwards through the 22.5o reducing elbow (22.5o angle to horizontal axis). If diameters...

  1. Consider water flowing upwards through the 22.5o reducing elbow (22.5o angle to horizontal axis). If diameters of the elbow at entrance point and exit points are 0.02540 m and 0.01905 m respectively, elbow is 0.08 m high, velocities of water are 5 m/s and 9 m/s at entrance point and exit point respectively, and density of water is 1000 kg/m3, moment flux correction factor = 1.02.
  1. Determine gage pressure at inlet
  1. Determine horizontal component of force of the system

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Consider water flowing upwards through the 50o reducing elbow.If diameters of the elbow at entrance point...
Consider water flowing upwards through the 50o reducing elbow.If diameters of the elbow at entrance point and exit points are 0.027 m and 0.0167 m respectively, elbow is 0.07 m high, velocities of water are 5 m/s and 9 m/s at entrance point and exit point respectively, and density of water is 1000 kg/m3, moment flux correction factor = 1.03. what is gage pressure and force in horizontal direction
Water is flowing into a factory in a horizontal pipe with a radius of 0.0163 m...
Water is flowing into a factory in a horizontal pipe with a radius of 0.0163 m at ground level. This pipe is then connected to another horizontal pipe with a radius of 0.0380 m on a floor of the factory that is 11.6 m higher. The connection is made with a vertical section of pipe and an expansion joint. Determine the volume flow rate that will keep the pressure in the two horizontal pipes the same. _________ m3/s
Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe...
Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe is 2.3 cm, and the radius of the nozzle is 0.41 cm. The speed of the water in the pipe is 0.74 m/s. Treat the water as an ideal fluid, and determine the absolute pressure of the water in the pipe.
Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe...
Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe is 1.8 cm, and the radius of the nozzle is 0.51 cm. The speed of the water in the pipe is 0.70 m/s. Treat the water as an ideal fluid, and determine the absolute pressure of the water in the pipe.
Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe...
Water flowing out of a horizontal pipe emerges through a nozzle. The radius of the pipe is 1.5 cm, and the radius of the nozzle is 0.55 cm. The speed of the water in the pipe is 0.65 m/s. Treat the water as an ideal fluid, and determine the absolute pressure of the water in the pipe.
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of...
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume...
1) 20 kg/min water at 20º C is mixed adiabatically with 40 kg/min water at 80...
1) 20 kg/min water at 20º C is mixed adiabatically with 40 kg/min water at 80 ºC. What is the outlet water temperature? Select one: a. 80 °C b. 60 °C c. 50 °C d. 70 °C 2) Steam at 0.8 MPa and 500 ºC is throttled over a well insulated valve to 0.6 MPa, what is the outlet temperature Select one: a. 450 ºC b. 500 ºC c. DOF>0 d. 400 ºC 3) Humid air at 70 C and...
A shell and-tube heat exchanger is required for the following service: Hot stream Cold Stream Aromatic...
A shell and-tube heat exchanger is required for the following service: Hot stream Cold Stream Aromatic Stream Cooling Water inlet Temperature (oC) 85 20 outlet Temperature (oC) 40 35 Mass Flowrate x heat Capacity (kW/oC) 85.2 Hot Stream cold stream (Cooling water) Heat Capacity (J/kg K) 2840 4193 Density (kg/m3) 750 999 Viscosity (cP) 0.34 1.016 Thermal conductivity (W/m.K) 0.19 0.594 Fouling Factor (m2.oC/W 0.00018 0.000176 ? The cooling water is allocated to the tube-side of the exchanger. ? It...