Question

Will metal dissolve during cathodic polarisation?

Will metal dissolve during cathodic polarisation?

Homework Answers

Answer #1

No,

Take an example--An increase in the copper corrosion rate during cathodic polarization in the potential range from –0.4 to –0.7 V is attributed to stirring of the near-electrode layer by evolving hydrogen bubbles. An addition of surface-active tetrabutylammonium iodide shifts the overpotential of hydrogen evolution and eliminates this effect. The copper dissolution rate during cathodic polarization is shown to be directly proportional to the reduction rate of dissolved oxygen. It is shown experimentally that H2O2 does not affect the dissolution rate of copper during cathodic polarization. The latter fact makes it possible to assume that oxygen reduction stages, which involve hydrogen peroxide, do not affect the anomalous dissolution of copper.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Steel is subject to severe cathodic polarisation by ~ -500 mV vs the open circuit potential...
Steel is subject to severe cathodic polarisation by ~ -500 mV vs the open circuit potential for 24 hours, in an aerated saline solution. Measured the pH of the solution after this experiment. Will the pH be the same as the initial pH, will it increase or decrease? Elaborate the answer in 1 sentence.
Part A Cathodic protection of iron involves using another more reactive metal as a sacrificial anode....
Part A Cathodic protection of iron involves using another more reactive metal as a sacrificial anode. Classify each of the following metals by whether they would or would not act as a sacrificial anode to iron. Drag each item to the appropriate bin. View Available Hint(s) Reset Help Ag Mg Cu Pb Sn Zn Au Will act as sacrificial anode for iron Will not act as sacrificial anode for iron Submit Part B An old iron beam was coated with...
What volume of 16M HNO3 is required to dissolve 0.50g of Cu metal? What volume is...
What volume of 16M HNO3 is required to dissolve 0.50g of Cu metal? What volume is actually used? Why is there a difference?
Determine if HNO3 can dissolve each of the following metal samples. 1) Write a balanced chemical...
Determine if HNO3 can dissolve each of the following metal samples. 1) Write a balanced chemical reaction showing how the 4.14 g Sn dissolves in HNO3. 2) Determine the minimum volume of 5.1 M HNO3 required to completely dissolve the sample.
The process of corrosion can be viewed as an electrochemical cell with cathodic reactions such as:...
The process of corrosion can be viewed as an electrochemical cell with cathodic reactions such as: O2+2H2O+4e−⟶4OH− at +1.229 V H++e−⟶1/2H2(g) at 0 V M2++2e−⟶M(s) Where M is a metal. If this is the case, and we assume iron serves as the anode, Fe0(s)⟶Fe+2(aq)+2e− at −0.447 V what must be true of the cathode reactions for corrosion to occur? a. The standard reduction potential of the cathode must be less than 0 V. b.  The standard reduction potential of the cathode...
Sulfuric acid dissolves aluminum metal according to the following reaction: 2Al(s)+3H2SO4(aq)→Al2(SO4)3(aq)+3H2(g) Suppose you wanted to dissolve...
Sulfuric acid dissolves aluminum metal according to the following reaction: 2Al(s)+3H2SO4(aq)→Al2(SO4)3(aq)+3H2(g) Suppose you wanted to dissolve an aluminum block with a mass of 15.1 g . What minimum mass of H2SO4 would you need? What mass of H2 gas would be produced by the complete reaction of the aluminum block?
Sulfuric acid dissolves aluminum metal according to the following reaction: 2Al(s)+3H2SO4(aq)--->Al2(SO4)3(aq)+3H2(g) Suppose you wanted to dissolve...
Sulfuric acid dissolves aluminum metal according to the following reaction: 2Al(s)+3H2SO4(aq)--->Al2(SO4)3(aq)+3H2(g) Suppose you wanted to dissolve an aluminum block with a mass of 14.2 g. A) What minimum mass of H2SO4 would you need? B) What mass of H2 gas would be produced by the complete reaction of the aluminum block?
Experiment: Synthesis and Characterization of a Metal-Organic Framework (MOF) Procedure: In a 100 mL jar, dissolve...
Experiment: Synthesis and Characterization of a Metal-Organic Framework (MOF) Procedure: In a 100 mL jar, dissolve 0.45 g (1.5 mmol) of zinc nitrate hexahydrate and 0.083 g (0.50 mmol) 1,4-benzenedicarboxylic acid (H2BDC) in 49 mL of dimethylformamide (DMF) and 1 mL DI water. Screw the lid on the jar. Heat the reaction mixture in an oven at 100 °C for at least 7 h. Cool to room temperature. In the hood, decant the solvent, and remove one or two crystals...
why voltage remains constant during discharge of nickel metal halide
why voltage remains constant during discharge of nickel metal halide
Sulfuric acid dissolves aluminum metal according to the following reaction: 2Al(s)+3H2SO4(aq)→Al2(SO4)3(aq)+3H2(g) Suppose you wanted to dissolve...
Sulfuric acid dissolves aluminum metal according to the following reaction: 2Al(s)+3H2SO4(aq)→Al2(SO4)3(aq)+3H2(g) Suppose you wanted to dissolve an aluminum block with a mass of 15.3 g . Part A: What minimum mass of H2SO4 would you need? Express your answer in grams. Part B: What mass of H2 gas would be produced by the complete reaction of the aluminum block? Express your answer in grams.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT