Question

A 40-mm-thick plain wall of thermal conductivity 0.04 W/m-K and of temperature 304 K is exposed...

A 40-mm-thick plain wall of thermal conductivity 0.04 W/m-K and of temperature 304 K is exposed to both cold fluid and surroundings both at 298 K. The cold fluid and wall provide that the heat transfer coefficient is 10.5 W/m2-K and the emissivity of the wall is 0.83. Given that the area of the wall is 1.5m2 If the total heat transferred is 140.6987W, find the temperature of the other side of the plain wall
Engineering   Chemical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

See the attachment below

Hope this helps

Thank you !!

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
71 mm thick horizontal plate made of an opaque material of thermal conductivity k= 25 W/m-K....
71 mm thick horizontal plate made of an opaque material of thermal conductivity k= 25 W/m-K. At the bottom, water flows at a temperature of T∞,w = 25C, whereas air flows at the top of the plate at T∞,a = 710 C having convection coefficient of ha= 71 W/m2-K. Assuming a diffused top of the plate that receives an irradiated flux of 7100W/m2, of which 30% is reflected back. The top and bottom surface temperatures are maintained at 43 C...
Gas with a thermal conductivity of k = 0.04 W/mk and prandtl number of 0.7 is...
Gas with a thermal conductivity of k = 0.04 W/mk and prandtl number of 0.7 is flowing at anaverage velocity of 0.5 m/s through a 2 mm diameter tube at a Reynolds number of 50. The heat capacity rate for the gas flowing through the tube is 0.001 kJ/s. The inlet temperature of the gas is 20C. There is a constant heat flux of 200 W/m^2 transferred from the tube wall into the gas. a) What is the Nu at...
The thermal conductivity of a sheet of rigid,extruded insulation is k = 0.020 W/(m*K). The measured...
The thermal conductivity of a sheet of rigid,extruded insulation is k = 0.020 W/(m*K). The measured temperature difference across a 30-mm-thick sheet of the material is T1-T2=10 C. a.) Assuming 1-D, steady state conditions withouth thermal energy generation in the material, what is the heat flux through a 2 m x 3 m sheet of the insulation? b.) What would be the effect on the rate of heat transfer through the sheet if a material with a relatively higher thermal...
A flat wall is exposed to an environmental temperature of 38 degrees C. The wall is...
A flat wall is exposed to an environmental temperature of 38 degrees C. The wall is covered with a layer of insulation 2.5 cm thick whose thermal conductivity is 1.8 W/(m.K), and the temperature of the wall on the inside of the insulation is 320 degrees C. The wall loses heat to the environment by convection. Compute the value of the convection heat transfer coefficient that must be maintained on the outer surface of the insulation to ensure that the...
1. Consider a 1.8-m high and 1.5 m-wide double-pane window consisting of two 4-mm thick layers...
1. Consider a 1.8-m high and 1.5 m-wide double-pane window consisting of two 4-mm thick layers of glass (k = 0.78 W/m°C) separated by a 10-mm wide stagnant air space (k = 0.026 W/m°C). The room is maintained at 20°C while the temperature of the outdoors is -10°C. Take the convective heat transfer coefficients on the inner and outer surfaces of the window to be 10 W/m2°C and 40 W/m2°C, respectively. Determine the steady rate of heat transfer through this...
A house has a composite wall of wood (exterior) (k = 0.12 W m-1 K -1...
A house has a composite wall of wood (exterior) (k = 0.12 W m-1 K -1 , 20 mm thick), fibreglass insulation (k = 0.045 W m-1 K -1 , 70 mm thick) and plasterboard (interior) (k = 0.25 W m-1 K -1 , 10 mm thick). Determine the total heat loss through the wall when the inside temperature is 20 °C, the outside temperature is -10 °C, the inside heat transfer coefficient is 15 W m-2 K -1 ,...
A 1-shell-2-tube pass heat exchanger is made of a steel alloy (thermal conductivity 45.4 W/(m K)....
A 1-shell-2-tube pass heat exchanger is made of a steel alloy (thermal conductivity 45.4 W/(m K). It is used to cool distilled water from 34oC to 29oC using water which flows inside tubes with an outer diameter of 19 mm and an inner diameter of 16 mm. The number of tubes in the shell is 160 (80 per pass). The mass flow rate of distilled water in the shell is 76180 kg/h. The cold water enters the heat exchanger at...
A certain material has a thermal conductivity of 0.90 W/(m oC). If the area of a...
A certain material has a thermal conductivity of 0.90 W/(m oC). If the area of a wall made of the material is 20 m2, the thickness of the wall is 0.6 m, and the heat transfer through that wall by conduction is 400 W, what is the temperature difference between the surfaces of the wall? Give your answer in terms of oC . (Enter the number only -- do not include the units in your answer.)
a) A 12 mm diameter mild steel sphere (k = 42.5 W/m K) is exposed to...
a) A 12 mm diameter mild steel sphere (k = 42.5 W/m K) is exposed to cooling airflow at 27 0C resulting in the convective coefficient, h = 114 W/ m2 K. The relevant properties of mild steel are given as follows: Density , /7850 2 mkg  Specific heat K kgJc p / 475 and thermal diffusivity hr m /043.0 2  Determine: (i) Time required to cool the sphere (lumped parameter system) from 540 0C to 950C. [7...
Select 1 m / s for a wall-illuminated 3 mm, inner 10 mm, 100 m long...
Select 1 m / s for a wall-illuminated 3 mm, inner 10 mm, 100 m long pipe, the incoming fluid entering 85 is cooled to 75 ℃. Apart from the pipe, there is a heat transfer coefficient of 7.8 W / m2.K and cross flowing water. a) Calculate the temperature before the fluid. b) Is the fluid flow laminar in the pipe? Is it turbulent? Why? c) Calculate the heat transfer coefficient between the fluid and the inner surface of...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT