Question

What brake horsepower would be required to pump water at 80 gpm with a 55 ft...

What brake horsepower would be required to pump water at 80 gpm with a 55 ft head if the pump is 75% efficient ?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
An 80% efficient pump draws 68.5 gallons per minute of water from an aquifer through a...
An 80% efficient pump draws 68.5 gallons per minute of water from an aquifer through a 4-inch ID pipe and discharges it through a 2-inch ID pipe to a tank, which is 100 ft above the water level in the aquifer. The friction loss in the pipe is 15 ft.lbf/lbm. What is the required pump horsepower?
What would be the required pump head (hP), in psi, to move water at 124gpm through...
What would be the required pump head (hP), in psi, to move water at 124gpm through a 3” commercial steel pipe, angled at 45 degrees, over a 75 ft high wall. Assume the pump draws water from an open reservoir, discharges at steady state, and ignore minor losses.
A centrifugal pump discharges 300 GPM through an 8-inch diameter impeller. The fluid leaves the impeller...
A centrifugal pump discharges 300 GPM through an 8-inch diameter impeller. The fluid leaves the impeller with a tangential velocity of 17 ft/sec. If water, @ 68°F, enters the impeller via radial flow (I.E. no whirl), and the inner radius and thickness of the impeller are 1.5-inches. (Assume a constant thickness of the impeller) and if the pump speed is 1750 rpm, with a head loss of 3.5-feet. What is the Torque on the shaft?
Pumps/Fluid Dynamics: A pump having Hpump= -1.8E-5×GPM2 + 1.2E-3×GPM + 350 is placed in a system...
Pumps/Fluid Dynamics: A pump having Hpump= -1.8E-5×GPM2 + 1.2E-3×GPM + 350 is placed in a system having Hsys = 12 + 2.5E-5×GPM1.9. The speed of the pump is changed, resulting in a new flow rate of 2,000 gpm. What head is required from the pump at the new condition?
A pump needs to move water from a lower reservoir to an upper reservoir at a...
A pump needs to move water from a lower reservoir to an upper reservoir at a rate of 600 cfs through a 9,000 ft long, 6-ft diameter pipeline (f = 0.03). For a 1,500 ft change in water surface elevation between the lower and upper reservoirs, compute the needed power input to the pump assuming a pump efficiency of 75% and that minor losses are negligible. In addition, compute the needed power input to the corresponding motor assuming the motor...
A tank is full of water. Find the work required to pump the water out of...
A tank is full of water. Find the work required to pump the water out of the spout. Use the fact that water weighs 62.5 lb/ft3. (Assume a = 6 ft, b = 9 ft, and c = 10 ft.)
Two alternative piping schemes are being considered by a water treatment facility. Head and horsepower are...
Two alternative piping schemes are being considered by a water treatment facility. Head and horsepower are reflected in the hourly cost of operation (information not needed for this problem). On the basis of a 10-year life and an interest rate of 12%, what is most nearly the number of hours of operation per year at which Alternative B becomes more cost efficient? Alternative A Alternative B Pipe diameter 4 in 6 in Head loss for required flow 48 ft 26...
3. Water flows through 80 ft of a 4” cast iron pipe. The head loss through...
3. Water flows through 80 ft of a 4” cast iron pipe. The head loss through the pipe is 0.27 ft. What is the volume flow rate of water through the pipe, in cfs? [Type II]
A pump increases the pressure of in liquid water from 100 kPa at 25°C to 2,500...
A pump increases the pressure of in liquid water from 100 kPa at 25°C to 2,500 kPa. What is the minnimum horsepower motor required to drive the pump for a flow rate of 0.005 m3/s
Water at 30 ∘C is pressurized in a pump from 80 kPa to 1600 kPa. If...
Water at 30 ∘C is pressurized in a pump from 80 kPa to 1600 kPa. If this requires 1.82 kJ for every kg of water that moves through the pump, then what is the isentropic efficiency of the pump? (Assume the mechanical efficiency is 100%)
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT