Question

Determine the maximal diameter of the hole For the fit Φ 48F7/g6 is

Determine the maximal diameter of the hole

For the fit Φ 48F7/g6 is

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A hole and a shaft system has a nominal dimension of 30 mm with a fit...
A hole and a shaft system has a nominal dimension of 30 mm with a fit type H7h8 fit. Determine: Fundamental Deviation of the Shaft Fundamental Deviation of the Hole If the nominal diameter lies within the range of 18 and 30, find the maximum and minimum size of the hole. Maximum and minimum size of hole Maximum and minimum size of shaft Width of the tolerance zone for hole and shaft
A rivet is to be inserted into a hole. If the standard deviation of hole diameter...
A rivet is to be inserted into a hole. If the standard deviation of hole diameter exceeds 0.02 mm, there is an unacceptably high probability that the rivet will not fit. A random sample of n = 15 parts is selected, and the hole diameter is measured. The sample standard deviation of the hole diameter measurements is s = 0.016mm. At α = 0.05 conduct a hypothesis test to investigate to indicate that the standard deviation of hole diameter exceeds...
A brass ring with inner diameter 2.00 cm and outer diameter 3.00 cm needs to fit...
A brass ring with inner diameter 2.00 cm and outer diameter 3.00 cm needs to fit over a 2.00-cm-diameter steel rod, but at 20 degrees Celsius the hole through the brass ring is 40 μm too small in diameter. To what temperature, in degrees Celsius, must the rod and ring be heated so that the ring just barely slips over the rod?
A cylindrical pin of diameter 20 cm, made of aluminum, does not fit through a 19.97cm...
A cylindrical pin of diameter 20 cm, made of aluminum, does not fit through a 19.97cm circular hole in a copper plate. The pin and the copper plate both are initially at a temperature of 110 degrees C. At what temperature, in degrees C, does the cylindrical pin just fit into the circular hole of the copper plate if both the plate and the pin are cooled together?
A 0.13 inch diameter hole is punched in the bottom of a 2.1 inch diameter can....
A 0.13 inch diameter hole is punched in the bottom of a 2.1 inch diameter can. The can is open at the top and contains 20 oz of liquid. What is the initial velocity of the liquid coming out of the hole? (include units with answer)
A hole in an Aluminum plate has diameter of 1.235 cm at 200C [???= 25 ×...
A hole in an Aluminum plate has diameter of 1.235 cm at 200C [???= 25 × 10−6?0−1, ???= 75 × 10−6?0−1] i. What is the diameter of the hole at 2000C? ii. At what temperature is the diameter of the hole equal to 1.176 cm?
At 20∘C, the hole in an aluminum ring is 2.100 cm in diameter. You need to...
At 20∘C, the hole in an aluminum ring is 2.100 cm in diameter. You need to slip this ring over a steel shaft that has a room-temperature diameter of 2.107 cm To what common temperature should the ring and the shaft be heated so that the ring will just fit onto the shaft? Coefficients of linear thermal expansion of steel and aluminum are 12×10−6 K−1 and 23×10−6 K−1 respectively.
In an interference force fit in a basic hole system, the allowance is: (a) zero (b)negative...
In an interference force fit in a basic hole system, the allowance is: (a) zero (b)negative (c)positive (d)greater than the tolerance of either the hole of the shaft (e)equal to the nominal or basic dimension
A 2 inch diameter hole is in the side of a water tank, and it is...
A 2 inch diameter hole is in the side of a water tank, and it is located 10 feet below the water level in the tank. What is the velocity of water exiting the hole and how will the velocity of the water exiting the hole change as the tank empties?
At 20∘C, the hole in an aluminum ring is 2.200 cm in diameter. You need to...
At 20∘C, the hole in an aluminum ring is 2.200 cm in diameter. You need to slip this ring over a steel shaft that has a room-temperature diameter of 2.204 cm . To what common temperature should the ring and the shaft be heated so that the ring will just fit onto the shaft? Coefficients of linear thermal expansion of steel and aluminum are 12×10-6K-1 and 23×10-6K-1 respectively. Express your answer in degrees Celsius to two significant figures.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT