Question

Design a Differentiator Op-amp circuit. First derive a an expression for Av= vo/vi. Then assign values...

Design a Differentiator Op-amp circuit. First derive a an expression for Av= vo/vi. Then assign values to circuit components verify your design with a PSpice simulation.

Homework Answers

Answer #1

Pspice code


* OPAMP DIFFERENTIATOR
.LIB NOM.LIB
X 0 2 7 4 6 UA741
R1 2 6 1K
C1 1 2 2U
Vdd 7 0 DC 12V
Vss 0 4 DC 12V
Vin 1 0 PWL(0 0 .5M 5 1M 0 1.5M 5 2M 0 2.5M 5 3M 0 3.5M 5 4M 0)
.TRAN 10NS 4MS
.PROBE
.END

Output waveforms

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Use an ideal op amp to design a differentiator circuit having a time constant of 10-5s...
Use an ideal op amp to design a differentiator circuit having a time constant of 10-5s using a 1-nF capacitor. Sketch the magnitude and phase response of the circuit, indicating the frequency at which the magnitude response equals 0 dB. A series input resistor is added to limit the gain magnitude at high frequencies to 100 V/V. Sketch the magnitude and phase responses of this modified circuit on the same axes as the ideal differentiator. How does the phase response...
Design an op-amp circuit that will provide an output voltage equal to the average of three...
Design an op-amp circuit that will provide an output voltage equal to the average of three input voltages. You may assume that the input voltages will be confined to the range -10V ?Vin ?10V. Verify your design by using Multisim software and a suitable set of input voltages.
Design an op-amp circuit for a weighted summer that shifts the dc level of the input...
Design an op-amp circuit for a weighted summer that shifts the dc level of the input signal vi(t) = 3 sin(t) V from zero to -3 V. Assume that in addition to vi(t), you have a dc voltage source of 1.5 V available. Sketch the output signal waveform.
Using a 741 op-amp for every stage, design this circuit: The input stage has a voltage...
Using a 741 op-amp for every stage, design this circuit: The input stage has a voltage gain of 10 and input impedance of 50 K?. The low pass filter stage has a Sallen-Key (VCVS) third order butterworth response and a cutoff frequency of 5KHz. The output buffer stage has a voltage gain of 10.
Design a multi-stage op-amp network that takes an input signal of vin(t) = 5 cos(120πt) V...
Design a multi-stage op-amp network that takes an input signal of vin(t) = 5 cos(120πt) V and outputs vout(t) = 2.5 + 2.5 sin(120πt) V. All resistors used must have values of at least 1 kΩ. Verify your design behaves as required using LTSpice XVII. (20 points)
Design an Op-Amp Circuit that takes an input from a low current capacity voltage source (i.e....
Design an Op-Amp Circuit that takes an input from a low current capacity voltage source (i.e. a high internal impedance source) with voltage range of -15mV to 15mV, amplify it, adds a DC offset so that the voltage is always positive filter it (LPF 1, 18.3 KHz) and the convert it into digital output (reference voltage of ADC 12V). Also determine the minimum sampling rate of ADC
Q.1.It is required to design an iterative combinational circuit that computes the equation Z=2*X-3, where X...
Q.1.It is required to design an iterative combinational circuit that computes the equation Z=2*X-3, where X is an n-bit signed number in 2’s complement representation. (Hint: -3 can be represented as -1+-1+-1 in 2’s complement representation, where -1 is represented as 111…..111). a)Determine the number of inputs and outputs needed for your 1-bit cell. Explain the meaning of values in the interface signals. b)Derive the truth table of your 1-bit cell. c) Derive minimized equations for your 1-bit using K-Map...