Question

By using only two resistors, R1 and R2, a student is able to obtain resistances of...

By using only two resistors, R1 and R2, a student is able to obtain resistances of 2 ­, 3 ­, 6 ­, and 9­. The values of R1 and R2 (in ohms) are:

Homework Answers

Answer #1

With 3, 6 ohm resistors, one get 2, 3, 6 and 9 ohm resistances assuming that resistors are to be used once.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
If two resistors with resistances R1 and R2 are connected in parallel, as in the figure...
If two resistors with resistances R1 and R2 are connected in parallel, as in the figure below, then the total resistance R, measured in ohms (Ω), is given by 1/R= 1/R1+1/R2 If R1 and R2 are increasing at rates of 0.3 Ω/s and 0.2 Ω/s, respectively, how fast is R changing when R1 = 80 Ω and R2 = 110 Ω? (Round your answer to three decimal places.)
If two resistors with resistances R1 and R2 are connected in parallel, as in the figure...
If two resistors with resistances R1 and R2 are connected in parallel, as in the figure below, then the total resistance R, measured in ohms (Ω), is given by 1 R = 1 R1 + 1 R2 . If R1 and R2 are increasing at rates of 0.3 Ω/s and 0.2 Ω/s, respectively, how fast is R changing when R1 = 50 Ω and R2 = 60 Ω? (Round your answer to three decimal places.)
If R is the total resistance of three resistors, connected in parallel, with resistances R1, R2,...
If R is the total resistance of three resistors, connected in parallel, with resistances R1, R2, R3, then 1 R = 1 R1 + 1 R2 + 1 R3 . If the resistances are measured in ohms as R1 = 40 Ω, R2 = 25 Ω, and R3 = 32 Ω, with a possible error of 0.5% in each case, estimate the maximum error in the calculated value of R. (Round your answer to three decimal places.)
Consider a simple circuit with two resistors connected in parallel. R1 = 30.0 Ohm, R2 =...
Consider a simple circuit with two resistors connected in parallel. R1 = 30.0 Ohm, R2 = 10.0 Ohm, and a 12 V battery Calculate the following values to one decimal places (enter just the number) The equivalent resistance  Ohms The voltage across resistor R1  V The voltage across resistor R2  V The current through resistor R1  A The current through resistor R2  A Consider a simple circuit with two resistors connected in series. R1 = 1.0 Ohm, R2 = 7.0 Ohm, and a 12 V...
Two resistors, with resistance R1= 5 ohms and R2=25 ohms are connected in series in a...
Two resistors, with resistance R1= 5 ohms and R2=25 ohms are connected in series in a circuit. The current flow generates heat at a rate of 1280 J/s in R1. What is the voltage drop across R2?
Assume you are given two resistors with resistances R1=4.0 kΩ and R2=6.0 kΩ and two capacitors...
Assume you are given two resistors with resistances R1=4.0 kΩ and R2=6.0 kΩ and two capacitors with capacitances C1=4.0 µF and C2=6.0 µF. a) Calculate the equivalent resistances Req and the equivalent capacitance Ceq if the resistors are connected in series and the capacitors are connected in parallel. b) Now, use the Req and Ceq that you calculate in part (a) to construct an RC circuit. If an emf of 27 V is suddenly applied across Req and Ceq, calculate...
Assume you are given two resistors with resistances R1=8.0 kΩ and R2=4.0 kΩ and two capacitors...
Assume you are given two resistors with resistances R1=8.0 kΩ and R2=4.0 kΩ and two capacitors with capacitances C1=8.0 µF and C2=4.0 µF. a)      Calculate the equivalent resistances Req and the equivalent capacitance Ceq if both the resistors and the capacitors are connected in parallel. b)      Now, use the Req and Ceq that you calculate in part (a) to construct an RC circuit. If an emf of 27 V is suddenly applied across Req and Ceq, calculate the charge on...
Assume you are given two resistors with resistances R1=4.0 kΩ and R2=6.0 kΩ and two capacitors...
Assume you are given two resistors with resistances R1=4.0 kΩ and R2=6.0 kΩ and two capacitors with capacitances C1=4.0 µF and C2=6.0 µF. a)      Calculate the equivalent resistances Req and the equivalent capacitance Ceq if the resistors are connected in parallel and the capacitors are connected in series. b)      Now, use the Req and Ceq that you calculate in part (a) to construct an RC circuit. If an emf of 27 V is suddenly applied across Req and Ceq, calculate...
Explain why the resistance of two resistors in series is R1 + R2, while two resistors...
Explain why the resistance of two resistors in series is R1 + R2, while two resistors in parallel give R1R2/(R1 + R2).
A power supply of 47 V is connected to two resistors of R1=47000 ohms and R2=31000...
A power supply of 47 V is connected to two resistors of R1=47000 ohms and R2=31000 ohms back to back (series circuit). What does the reading say in a voltage meter that has a inner resistance of 89000 ohms that is connected to the first resister (R1)?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT