Question

It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz]...

It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz] with a circuit that provides a charge of 18 V (DC) with a maximum ripple percentage of 10%. The charge consumes on average 400*10^-3 Ampere. The diodes used have a decreace of 0.8 V.

A) Design a rectifier of half wave that complies with the requirements.  [Output Voltage: Provides a charge of 18 V (DC) with a maximum ripple percentage of 10%.]

B) Design a rectifier of complete wave using diode bridges for the given problem.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz]...
It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz] with a circuit that provides a charge of 18 V (DC) with a maximum ripple percentage of 10%. The charge consumes on average 400*10^-3 Ampere. The diodes used have a decreace of 0.8 V. A) Design a rectifier of half wave that complies with the requirements. B) Design a rectifier of complete wave using diode bridges for the given problem. [The Output Voltage is...
Full wave rectifier is used to design a DC power supply. The DC power supply has...
Full wave rectifier is used to design a DC power supply. The DC power supply has an average output voltage of 12v on which the maximum ripple allowed is 1v (peak to peak). The rectifier feeds a load of 200ohm . The rectifier is supplied from 170v at 60 hz ac line through a transformer. Assume Vy= 0.7v . a) Find the transformer tarns ratio? b) Find the required value of the capacitor? c) Specify the PIV rating of the...
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a...
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a series inductance, resistance and dc voltage source, with L = 100 mH, R = 10 Ω, and Vdc = 50 V. a). Determine an expression for load current. b). Determine the power absorbed by the dc voltage source. c). Determine the power absorbed by the resistance. d). Determine the power factor of the source.
If the available power source is a single-phase, 60 Hz, ac supply and a separately excited...
If the available power source is a single-phase, 60 Hz, ac supply and a separately excited DC motor is to be fed from this source, configure possible drive circuits for: i) One-Quadrant Operation, ii) Two- Quadrant Operation iii) Four- Quadrant Operation Hints: For one-quadrant operation, the motor control circuit is a half-wave controlled rectifier or a semicontrolled converter and the driver for the separately excited is a semi-controlled converter with a freewheeling diode using the ac supply source. For two-quadrant...
Your group has been asked to design a portion of a power supply which reduces the...
Your group has been asked to design a portion of a power supply which reduces the variation due to ripple from the rectifier stage. The completed power supply is intended to provide 300W of 48V DC power to an RF transmitter. The transformer stage transforms a 3-phase AC power source at 60 Hz from 120 V RMS to 50V RMS, which is rectified before being applied to your circuit. You are designing the regulator, not the rectifier. The input to...
An ac generator with an rms voltage 120 V is and a frequency of 60 Hz...
An ac generator with an rms voltage 120 V is and a frequency of 60 Hz is connected with a 15 µF capacitor, and a 30 mH inductor and a resistor R.     What value must R have if the rms current in this circuit it to be 5 mA?       Calculate the rms voltage across the resistor.
Your group has been asked to design a portion of a power supply which reduces the...
Your group has been asked to design a portion of a power supply which reduces the variation due to ripple from the rectifier stage. The completed power supply is intended to provide 300W of 48V DC power to an RF transmitter. The transformer stage transforms a 3-phase AC power source at 60 Hz from 120 V RMS to 50V RMS, which is rectified before being applied to your circuit. You are designing the regulator, not the rectifier. The input to...
An AC source operating at 60 Hz with a maximum voltage of 173 V is connected...
An AC source operating at 60 Hz with a maximum voltage of 173 V is connected in series with a resistor (R = 1.2 k?) and a capacitor (C = 2.5 µF). (a) What is the maximum value of the current in the circuit? (b) What are the maximum values of the potential difference across the resistor and the capacitor? ?VR,max = ?VC,max = (c) When the current is zero, what are the magnitudes of the potential difference across the...
A series circuit includes an AC power supply with peak voltage 5.4 V and frequency 100...
A series circuit includes an AC power supply with peak voltage 5.4 V and frequency 100 Hz, a 10-ohm resistor and a 120 uF capacitor. What is the impedance, phase angle, and maximum current? Sketch one cycle of the voltage and current as might be seen on an oscilloscope.
A capacitor is connected across an AC generator whose frequency is 31 Hz and has a...
A capacitor is connected across an AC generator whose frequency is 31 Hz and has a peak voltage 124 V. The rms current in the circuit is 33 A. a) What is the capacitance of the capacitor? Cmax = __________ F b) What is the magnitude of the maximum charge on one plate of the capacitor? Qmax = __________ C
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT