Question

Full wave rectifier is used to design a DC power supply. The DC power supply has...

Full wave rectifier is used to design a DC power supply. The DC power supply
has an average output voltage of 12v on which the maximum ripple allowed is 1v
(peak to peak). The rectifier feeds a load of 200ohm . The rectifier is supplied from
170v at 60 hz ac line through a transformer. Assume Vy= 0.7v .
a) Find the transformer tarns ratio?
b) Find the required value of the capacitor?
c) Specify the PIV rating of the diodes?
d) Find the percent time where the diode d1 is conduct?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with a peak-to-peak riple of 2V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac volatage sources of any amplitudes needed are avaialable. Draw the circuit diagram for your design, Specify the values of all components used. 2. Repeat Problem 1 with 2 diodes and out-of-phase voltage sources to form a full-wave rectifier.
Design a full-wave bridge rectifier circuit to deliver 10 volts DC with less than 0.1 volt...
Design a full-wave bridge rectifier circuit to deliver 10 volts DC with less than 0.1 volt peak-to-peak ripple into a 1 k load. Assume a 60 Hz input sin wave.
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60...
Design and simulate a Half and Full wave rectifier for a 12V AC supply with 60 Hz frequency.
Your group has been asked to design a portion of a power supply which reduces the...
Your group has been asked to design a portion of a power supply which reduces the variation due to ripple from the rectifier stage. The completed power supply is intended to provide 300W of 48V DC power to an RF transmitter. The transformer stage transforms a 3-phase AC power source at 60 Hz from 120 V RMS to 50V RMS, which is rectified before being applied to your circuit. You are designing the regulator, not the rectifier. The input to...
Your group has been asked to design a portion of a power supply which reduces the...
Your group has been asked to design a portion of a power supply which reduces the variation due to ripple from the rectifier stage. The completed power supply is intended to provide 300W of 48V DC power to an RF transmitter. The transformer stage transforms a 3-phase AC power source at 60 Hz from 120 V RMS to 50V RMS, which is rectified before being applied to your circuit. You are designing the regulator, not the rectifier. The input to...
It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz]...
It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz] with a circuit that provides a charge of 18 V (DC) with a maximum ripple percentage of 10%. The charge consumes on average 400*10^-3 Ampere. The diodes used have a decreace of 0.8 V. A) Design a rectifier of half wave that complies with the requirements.  [Output Voltage: Provides a charge of 18 V (DC) with a maximum ripple percentage of 10%.] B) Design a...
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a...
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a series inductance, resistance and dc voltage source, with L = 100 mH, R = 10 Ω, and Vdc = 50 V. a). Determine an expression for load current. b). Determine the power absorbed by the dc voltage source. c). Determine the power absorbed by the resistance. d). Determine the power factor of the source.
It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz]...
It is required to connect the Electric Power Company - [120 V (AC), frequency 60 Hz] with a circuit that provides a charge of 18 V (DC) with a maximum ripple percentage of 10%. The charge consumes on average 400*10^-3 Ampere. The diodes used have a decreace of 0.8 V. A) Design a rectifier of half wave that complies with the requirements. B) Design a rectifier of complete wave using diode bridges for the given problem. [The Output Voltage is...
Assume you only have an AC power supply in the lab but you need DC power...
Assume you only have an AC power supply in the lab but you need DC power for your application. Design, simulate and build a DC power supply. Design requirements: AC voltage: 2.5 Vp-p , f=60Hz DC voltage output: 1V (As close to 1V as possible) with the smallest ripple step possible. Filter frequency equation: f= 1/(2(pi)(R)(C))
Design a DC power supply that will deliver 100mA of current to a load with a...
Design a DC power supply that will deliver 100mA of current to a load with a ripple of 5%. Use a full wave rectifier and a 17 Peak Voltage Source with F= 60 Hz. Load resistance = 1k So Basically you just need to find the capacitance of the filtering capacitor. Please tell me how. This is what I did, but I think I'm wrong. The Vripple I got is (.05)*17 = .85 V. Then according to my manual, C...