Question

During laboratory testing of a 6-inch steel-alloy rod with a cross sectional area of 0.32in², a...

During laboratory testing of a 6-inch steel-alloy rod with a cross sectional area of 0.32in², a tensile load of 40,000 lbs is applied. If the cross sectional area decreases to 0.3188in² and lengthens to 6.021 inches, what is the Poisson’s Ratio?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Two steel rods each of cross sectional area 500mm2, and an aluminium alloy rod, of cross...
Two steel rods each of cross sectional area 500mm2, and an aluminium alloy rod, of cross sectional area 600 mm2 are cut to a length of 3m and attached to rigid end plates to form a composite member. If a tensile force of 100kN is applied to the member and at the same tie the temperature of the system is lowered by 20℃, determine the force developed in each of the rods and the extension of the member. What further...
1. A polyethylene rod exactly 10 inches long with a cross-sectional area of 0.04 in2 is...
1. A polyethylene rod exactly 10 inches long with a cross-sectional area of 0.04 in2 is used to suspend a weight of 514 lbs-f (pounds-force). Given the tensile modulus for this polymer is  25,000 psi and the viscosity is 3 × 109 psi-sec, calculate the length of the rod, in inches, 1 hour(s) after loading. Answer Format: X.XX Unit: inches 2. A polymeric cylinder initially exerts a stress with a magnitude (absolute value) of 1.437 MPa when compressed. If the tensile...
Two square-cross-section rods, one steel and the other copper, are welded end to end. Each rod...
Two square-cross-section rods, one steel and the other copper, are welded end to end. Each rod is 0.81 m long and has square side length of 3/8 inch on the ends. The combination is subjected to a tensile force with magnitude 4500 N. Part A For the steel rod, what is the elongation? Part B For the copper rod, what is the elongation?
A steel bar has cross-sectional area A=10-3 m2, Young modulus E= 2 x 1011 Pa and...
A steel bar has cross-sectional area A=10-3 m2, Young modulus E= 2 x 1011 Pa and Poisson’s ratio of 0.4. The steel bar has a rectangular cross sectional area. a.         If the bar is subject to a compressive force of 105 N, find the corresponding longitudinal and transverse strains.                                                    [3 marks] b.         Two strain gauges, each with unstrained resistance of 120 Ω and a gauge factor of 2.0 are bonded on to the top surface of the steel bar....
You have a nominal 3.5-inch diameter tube steel pipe, 18 feet high that is embedded into...
You have a nominal 3.5-inch diameter tube steel pipe, 18 feet high that is embedded into a concrete foundation.  Neglecting the weight of the column, answer the questions below: What is the maximum vertical load this pipe can support/critical load (lb)? If a vertical load of 2,500 lbs and a horizontal force of 150 lbs are applied at the top of the column, what are the maximum combined tensile and compressive stresses (psi) where the column meets its foundation?  Are they allowable?
A uniform rope of cross-sectional area 0.95 cm2 breaks when the tensile stress in it reaches...
A uniform rope of cross-sectional area 0.95 cm2 breaks when the tensile stress in it reaches 5.50 ? 106 N/m2. (a) What is the maximum load (in N) that can be lifted slowly at a constant speed by the rope? ___________ N (b) What is the maximum load (in N) that can be lifted by the rope with an acceleration of 5.00 m/s2? ___________ N
The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70...
The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70 cm2, and its large piston has a cross-sectional area of 199 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 14.0 kN?
A brass rod and a lead rod, each 0.250 mm long and each with cross-sectional area...
A brass rod and a lead rod, each 0.250 mm long and each with cross-sectional area 2.00×10−4m22.00×10−4m2, are joined end to end to make a composite rod of overall length 0.500 mm. The free end of the brass rod is maintained at a high temperature, and the free end of the lead rod is maintained at a low temperature. The temperature at the junction of the two rods is 185.0∘C∘C and the heat current due to conduction through the composite...
What is PSF loading of the soil if, a 20-ton building transfers its load equally though...
What is PSF loading of the soil if, a 20-ton building transfers its load equally though a 1000 SF foundation to the earth? What is the expected force required to break a 6’ x 12” concrete cylinder made from 3000 PSI concrete? What is the stress in a no. 4 rod subjected to a force of 5000 lbs.? how many times stronger is a no. 8 rod compared to a no. 4 rod made of the same material (Compare cross...
A steel cable has a cross-sectional area 4.03 × 10-3 m2 and is kept under a...
A steel cable has a cross-sectional area 4.03 × 10-3 m2 and is kept under a tension of 3.07 × 104 N. The density of steel is 7860 kg/m3. Note that this value is not the linear density of the cable. At what speed does a transverse wave move along the cable?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT