Question
A brass rod and a lead rod, each 0.250 mm long and each with cross-sectional area...
A brass rod and a lead rod, each 0.250 mm long and each with cross-sectional area 2.00×10−4m22.00×10−4m2, are joined end to end to make a composite rod of overall length 0.500 mm. The free end of the brass rod is maintained at a high temperature, and the free end of the lead rod is maintained at a low temperature. The temperature at the junction of the two rods is 185.0∘C∘C and the heat current due to conduction through the composite rod is 6.00 WW.
(A) What is the temperature of the free end of the brass rod?
(B) What is the temperature of the free end of the lead rod?
Homework Answers
Answer #1
Not the answer you're looking for?
Similar Questions
A copper rod, an aluminum rod, and a brass rod, each of 6.00 m length and...
A copper rod, an aluminum rod, and a brass rod, each of 6.00 m
length and 1.00 cm diameter, are placed end to end with the
aluminum rod between the other two. The free end of the copper rod
is maintained at water’s boiling point, and the free end of the
brass rod is maintained at water’s freezing point. We know that
??????? = 401 W⁄m. K , ????????? = 235 W⁄m. K and ?????? = 109 W⁄m.
k. What...
Two steel rods each of cross sectional area 500mm2, and an aluminium alloy rod, of cross...
Two steel rods each of cross sectional area 500mm2,
and an aluminium alloy rod, of cross sectional area 600
mm2 are cut to a length of 3m and attached to rigid end
plates to form a composite member.
If a tensile force of 100kN is applied to the member and at the
same tie the temperature of the system is lowered by 20℃, determine
the force developed in each of the rods and the extension of the
member.
What further...
A Physics 4C student team is doing a thermal experiment where they have two rods of...
A Physics 4C student team is doing a thermal experiment where
they have two rods of different materials. One rod is made of
cooper and the other brass. They are joined together. The brass
section has a length of 0.355 m. The copper section a length of
0.750 m. Each segment has cross-sectional area of 0.00475 m^2.
Boiling water is in contact with the free end of the brass rod
while the free end of the copper is in contact...
1) A cylindrical copper rod of length 2 m and cross-sectional area of 5 cm^2 is...
1) A cylindrical copper rod of length 2 m and cross-sectional
area of 5 cm^2 is insulated to prevent heat loss through its
surface. The ends are maintained at a temperature difference of 100
C by having one end in a water-ice mixture and the other in a
boiling water/steam mixture. If you initially have 10 g of ice on
the one end and lots of steam on the other, how long does it take
to melt the ice?
2)...
A heat-conducting rod, 0.90 m long and wrapped in insulation, is made of an aluminum section...
A heat-conducting rod, 0.90 m long and wrapped in insulation, is
made of an aluminum section that is 0.20 m long and a copper
section that is .70m long. Both sections have a cross-sectional
area of .000040m2. The aluminum end and the copper end are
maintained at temperatures of 30 degrees C and 230 degrees C
respectively. The thermal conductivities of aluminum and copper are
205 W/m ∙ K (aluminum) and 385 W/m ∙ K (copper). What is the
temperature...
Two bars, A and B, each of length 2.0 m and cross sectional area 1.0 m2,...
Two bars, A and B, each of
length 2.0 m and cross sectional area 1.0 m2, are placed
end to end as shown in the figure.
The thermal conductivities of the bars are
kA = 439 J/(s ⋅⋅ m ⋅⋅ K) and
kB = 887 J/(s ⋅⋅ m ⋅⋅ K), respectively. The
left end of bar A is maintained at 373 K while the
right end of B is maintained at 273 K.
Which one of the following statements is...
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 4 minutes ago
asked 12 minutes ago
asked 23 minutes ago
asked 35 minutes ago
asked 45 minutes ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 2 hours ago