Question

If you perform a 1:4 dilution on a 20 mM NaCl stock, what is the final...

If you perform a 1:4 dilution on a 20 mM NaCl stock, what is the final concentration?

Homework Answers

Answer #1

1:4 dilution means 1 part of stock solution and 4 part of solvent so total volume will become 5 times of initial volume so concentration will become one fifth of initial concentration.

So the final concentration is 4 mM.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. How to make 20ml of 3M NaCl? 2. What is the percent concentration of 3M...
1. How to make 20ml of 3M NaCl? 2. What is the percent concentration of 3M NaCl? 3. What is the molar concentration of 10% NaCl?   4. Your stock solution is 5M NaCl and your goal is to make 25ml of 0.5M NaCl (all in water). What volume of stock should you use? 5. Make a reagent solution for enzymatic digestion of plasmid in water. The reaction conditions require: 2x digestion buffer                                                0.5% bovine serum albumin 10 mM sodium chloride...
A) You need to make 250ml of a 20x stock solution of NaCl to dilute later...
A) You need to make 250ml of a 20x stock solution of NaCl to dilute later to a final concentration of 50 mM. The M.W. of NaCl is 58.44. How would you accomplish this?       NaCl ___________ g       Pure Water __________ ml B) You need 3.5 L of 50 mM NaCl from your 20x stock. How would you accomplish this?      20x stock ______ ml      Pure water ________ ml C) You need to make 20 ml of a...
You are required to make up 500 mL of the following buffer: 50 mM NaCl, 1...
You are required to make up 500 mL of the following buffer: 50 mM NaCl, 1 % SDS, 50 uM KCl (these are the final concentrations of each component in this one buffer) You are provided with the three separate stock solutions: 10 M NaCL 20 % SDS 0.05 M KCl State how much of each component you add in order to achieve this: 10 M NaCL………… mL 20 % SDS…………. mL 0.05 M KCl…………… mL Distilled H20………. mL Final...
1. To prepare 20 mL of 15 mM NaCl, how much NaCl would you need to...
1. To prepare 20 mL of 15 mM NaCl, how much NaCl would you need to weigh? 2. To prepare 5 mL of 1 mM glucose, how much glucose would you need to weigh? How do you prepare 1 L of 1 mM NaCl using the NaCl solution you prepared in (1)? 3. How do you prepare 1 mL of 10 µM glucose using the glucose solution you prepared in (2)?
You also have the following stock solutions already made: 20% SDS, 5M NaCl, 500 mM EDTA,...
You also have the following stock solutions already made: 20% SDS, 5M NaCl, 500 mM EDTA, You have a 40% glycerol solution, and 10X TBE 1. Make 100 ml of 10% SDS, 1M NaCl 2. Make 100 ml of 10% glycerol solution 3. Make 40 ml of 0.5% agarose in 1X TBE solution Must show calculations. I always get confused with % solutions.
You need to perform a 1:25 dilution of a certain solution- what glassware will you need...
You need to perform a 1:25 dilution of a certain solution- what glassware will you need to make this dilute solution? (Note: assume you have only- 5.00,10.00,15.00 & 20.00 mL volumetric pipets, and 25.00 & 50.00 mL volumetric flasks. Also, draw a diagram.
6. (16 pts.) When you performed (or will perform) the atomic absorption experiment, you performed parallel...
6. (16 pts.) When you performed (or will perform) the atomic absorption experiment, you performed parallel dilutions (in lieu of serial dilutions) with a Zn2+ standardized solution, and used your analysis of these dilutions to construct a calibration curve relating the sensitivity of the instrument to the Zn2+ concentration In this problem, you are going to quantify the uncertainty in the concentrations of Zn2+ dilutions obtained from both serial and parallel dilutions and compare the results for the two methods....
You will prepare a serial dilution with 6 tubes. Into tube 1 you add 0.9 ml...
You will prepare a serial dilution with 6 tubes. Into tube 1 you add 0.9 ml NaCl and you add 0.5 ml NaCl into tubes 2-6. Next you add 0.1 ml of serum to tube 1 and mix and transfer 0.5 ml to tube 2. Continue making serial dilutions through tube 6 (discarding 0.5 ml from tube 6). Finally, you add 0.5 ml of sheep RBCs to EACH tube (1-6) What is the final dilution in each tube after the...
How would you prepare 2 L of 0.85% NaCl? (MW=58.44 g/mol) (2 pts) 2. You need...
How would you prepare 2 L of 0.85% NaCl? (MW=58.44 g/mol) (2 pts) 2. You need to do a 1/25th dilution, explain how you would achieve this dilution. (2 pts) 3.If you performed a 1/10th dilution two times, what is the final dilution. (2 pts) 4.Your protocol calls for working with a 1.5 x 10-4 M boric acid solution. To save shelf space, you decide to make up a 20X stock solution. What is the molarity of the stock solution...
1. a) You have a stock tube of 50 mM MgCl2 and you need to optimize...
1. a) You have a stock tube of 50 mM MgCl2 and you need to optimize MgCl2 concentration for the Q8 SYBR Green primers. Create a table to describe how you would create a dilution series so that MgCl2 could be tested at 5 mM, 4.5 mM, 3 mM, 2.5 mM, 1 mM, 0.5 mM and 0 mM to optimize a 25 l PCR (see the table below). Your new stocks should be in a 100 μL volume. b) Once...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT