Question

**If there is a room of 10 ft x 10 ft x 10 ft, what is the
rate of heating load to maintain the room temperature at
70 ^{o}F when the outside temperature is 10^{o}F.
Assume that there is no heat loss by conduction/convection, and 2
air exchange per hour (k=2).**

A 1296 Btu/hr

B 2160 Btu/hr

C 1080 Btu/hr

D 1620 Btu/hr

E 3780 Btu/hr

Answer #1

The surface temperature of 200 ft of 8-inch diameter
un-insulated pipe carrying steam at 335 F is 250 F. The pipe is
located in a room with air and surroundings at 50 F. The surface
emissivity of the pipe is 0.70. Calculate convection, radiation and
total heat loss from the pipe (Btu/hr). The pipe is insulated with
3 inches on insulation with thermal resistance R = 2 hr-ft2-F/Btu
per inch. The surface emissivity of the insulation is 0.70.
Calculate convection,...

Heat Removal of a Cooling Coil. A cooling coil
of 1.0 ft of 304 stainless-steel tubing having an inside diameter
of 0.25 in. and an outside diameter of 0.40 in. is being used to
remove heat from a bath. The temperature at the inside surface of
the tube is 40 degrees fahrenheit and is 80 degrees fahrenheit on
the outside. The thermal conductivity of 304 stainless steel is a
function of temperature:
k=7.75+7.78 x 10^-3T
where k is in btu/h*ft*fahrenheit...

A hot black painted pipe(2.54-cmO.D.and50-mlong)passesthrougha
20°C room to heat it. The temperature of the pipe surface is 150°C.
If the heat transfer coefficient by convection to the air is 10
W/m2-K :
a) What is the total heat rate loss?
b) What is the radiation heat transfer coefficient?
c) At what temperature of the pipe, the heat rate by convection
equals the heat rate by radiation.

A room with approximately 100 people measures 15m x 20m x 10 m
and the indoor temperature is 20 o C. Let's assume that
each person in the room gives an average of 350 kJ of heat per
hour. Find the room temperature at the end of 30 minutes, assuming
that the walls of the living room do not take heat and pass and
that the air conditioner does not work for 30 minutes.

A building has the following dimensions and characteristics:
footprint of 100 ft x 50 ft and 8 stories, 10 feet floor-to-floor
height for each floor. The window-wall ratio is .33. Walls have an
overall R-value of 20, windows have a U-value of 0.6. The roof has
an R value of 30. Building is programmed as all office with 150
square feet per person.
Part a Q, in BTUH, assuming heating design conditions of 74
degree F inside and 10 degree...

A 6.38-in-wide and 27-in-high vertical hot surface in 78°F air
is to be cooled by a heat sink with equally spaced fins of
rectangular profile. The fins are 0.08 in thick and 27 in long in
the vertical direction and have a height of 1.2 in from the base.
Consider base temperature to be 180°F. Given: The properties of air
at 1 atm and the film temperature at 129°F. k = 0.01597 Btu/h.ft.°F
v = 0.1975 x 10-3 ft2/s, Pr...

Air has a thermal conductivity of 3 x 10-4 J cm-1 s-1 K-1.
Consider a window with double panes
of glass where the temperature of the inside pane is 25 oC and the
temperature of the outside
pane is -5 oC. The size of the window is 40 cm x 60 cm, and the
panes are 8 mm apart. What is
the heat flow in watts through the window? You can ignore
convection.

In the first lesson we talk about the heat transfer that takes
place in the human body, but the same types of transfer occur for
any object. For the following question, use the dimensions and
characteristics of your own home. It’s reasonable to assume that
walls are thick enough to block direct heat loss to radiation
(without prior conduction through the walls). Windows are
relatively thin in comparison and conduct more heat than walls
(i.e. a double-pane glazed window has...

Homework-9
Due:
Q) A fuel plate is fabricated from 0.3 cm thick 1.5% enriched
uranium. The cladding is 0.25 mm 304 stainless steel. The coolant
saturation temperature is 260 oC. The
average thermal neutron flux is 2.5 X
1014
neutrons/cm2 /s. The surface
temperature of the clad is 350 oC.
Assume any missing data to answer the following questions:.
1) Write an expression of the heat generated per unit volume
2 What is the heat flux at the surface of...

1. An oven chimney is
made of brick with a heat transmission coefficient 1.1 W/mK 10 cm
thick. Since the shaft exterior radiation beam coefficient is 0.8
and the flue gas temperature is 350°C, the external ambient
temperature is 25°C and the outer ambient heat transport
coefficient is 20 W/m2K;
a) Calculate the shaft exterior
temperature.
b) In order to reduce the risk of burn
injury that may occur in the body, the shaft is asked to be below
55°Cve...

ADVERTISEMENT

Get Answers For Free

Most questions answered within 1 hours.

ADVERTISEMENT

asked 15 minutes ago

asked 24 minutes ago

asked 44 minutes ago

asked 51 minutes ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 2 hours ago

asked 2 hours ago

asked 2 hours ago