Question

Why FET is called unipolar device and is called as voltage operated device? What are the...

Why FET is called unipolar device and is called as voltage operated device? What are the important characteristics of FET?

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
What is the threshold voltage in millivolts for an NMOS FET with a source-to-body voltage, Vsb,...
What is the threshold voltage in millivolts for an NMOS FET with a source-to-body voltage, Vsb, of 887mV ? Assume that this MOSFET has a uniform body doping profile, with a P-type body doped with boron at a concentration of 2.0 x 10^17/cm^3. Also assume that this FET has an effective oxide thickness, Toxe, of 62 angstroms, and that it’s threshold voltage with Vsb = 0V is Vt0 = 411mV. Use: kT/q = 26mV and ni = 1.5 x 10^10/cm^3...
When is a device called an Ohmic device? A. No device is an Ohmic device. B....
When is a device called an Ohmic device? A. No device is an Ohmic device. B. Only when the device obeys Ohm's Law and has a non-linear relationship between potential and current. C. Only when the device obeys Ohm's Law and has a linear relationship between potential and current. D. All devices are Ohmic devices. Using Ohm's Law, keeping the resistance constant and increasing the applied voltage A. increases the current. B. stops the current. C. decreases the current. D....
An electrical device draws 5.44 A at 110 V. If voltage drops by 10.0 percent, what...
An electrical device draws 5.44 A at 110 V. If voltage drops by 10.0 percent, what will be the current, assuming nothing else changes?
A) When an alternating voltage of 200 V is applied across a device X, a current...
A) When an alternating voltage of 200 V is applied across a device X, a current of 0.4A flows through the circuit and is in phase with the applied voltage. When the same voltage is applied across another device Y, the same current again flows through the circuit, but it lags behind the applied voltage by π/2radians. Name the devices X and Y. Justify your answer.                                                                   b) A coil of inductance 0.50H and resistance 100 Ω is...
What do you think contributes the MOST to unipolar depression? (genetic factors, biochemical factors, brain anatomy,...
What do you think contributes the MOST to unipolar depression? (genetic factors, biochemical factors, brain anatomy, dysfunctional thinking, etc.) Please explain why
A voltmeter is a device placed in parallel with a circuit element to measure the voltage...
A voltmeter is a device placed in parallel with a circuit element to measure the voltage drop across the element. As it turns out, it is difficult (impossible?) to measure a voltage drop directly, so a voltmeter typically works by measuring a current and then converting to potential. At least before the days of digital circuitry, a voltmeter was basically an ammeter (which measures current) in series with a very large resistance R0. Suppose you use this kind of voltmeter...
When a flashlight is operated, what is being used up: battery current, battery voltage, battery energy,...
When a flashlight is operated, what is being used up: battery current, battery voltage, battery energy, battery power, or battery resistance? Explain your reasoning. On the other hand, the equation of power P = V2/R indicates that the power dissipated in a resistor of the flashlight decreases if the resistance is increased, whereas the equation P = I2R implies the opposite. Is there a contradiction here? Explain.
      Suppose a voltage divider is constructed from two fixed resistors. If VIN =  25 V,...
      Suppose a voltage divider is constructed from two fixed resistors. If VIN =  25 V, R1 =  108 Ω, what should the value of R2 be so that VOUT is  10 V? R2 =  ΩThe circuit diagrams display a device called a voltage divider.           
a) According to the principle of temperature dependence of the voltage called NTC thermistor and semiconductor...
a) According to the principle of temperature dependence of the voltage called NTC thermistor and semiconductor junction - enough information in terms of sensitivity and linearity (linearity) of working temperature sensors giving- compare. b) What parameters depends on the voltage produced by a thermo-couple?
a) According to the principle of temperature dependence of the voltage called NTC thermistor and semiconductor...
a) According to the principle of temperature dependence of the voltage called NTC thermistor and semiconductor junction - enough information in terms of sensitivity and linearity (linearity) of working temperature sensors giving- compare. b) What parameters depends on the voltage produced by a thermo-couple?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT