Question

Give the correct units (dB or dBm): the loss in a filter ____ The EIRP of...

Give the correct units (dB or dBm):

the loss in a filter ____
The EIRP of a transmitter ____
The output power of a transmitter _____
The signal detected by a receiver _____
The gain of an antenna _____

Homework Answers

Answer #1

1)the loss in a filter (dB)

the unit of loss in filter is always measured in dB

it is the ratio of signal level to the test confriguration without filter to the signal level with filter..

2)The EIRP of a transmitter (dBm)

effective/equivalent isotropic radiated power  is the measured radiated power in a single direction always measure in dBm

3) The output power of a transmitter (dBm)

it is define as the actual amount of power(in watts) of radio frequency (RF) energy that a transmitter produces at its output.. it is always measured in dBm

4)The signal detected by a receiver (dB)

always measured in dB

5)The gain of an antenna (dB)

it is the ratio of power produced byy the antenna from a far field source on the antenna's beam axis to power produced by hypothetical lossless isotropic antenna...

it is always measured in dB

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A fiber optic receiver has a sensitivity of -38 dBm. This is the optical power required...
A fiber optic receiver has a sensitivity of -38 dBm. This is the optical power required to operate with the desired mesage quality. The transmitter produces a power level of 4 dBm. What are the allowed system losses in dB? These losses are caused by inefficient coupling from the transmitter into the fiber, by connector and splice losses, and by losses in the fiber itself.
Consider the Voyager spacecraft, transmit frequency 8.4 GHz, transmitter power PT= 21.3 W, transmitting antenna gain...
Consider the Voyager spacecraft, transmit frequency 8.4 GHz, transmitter power PT= 21.3 W, transmitting antenna gain GT is 6.5 x 104 W/W at a distance of 6.8 x 1011m from Jupiter to Earth. Both the Voyager and earth based antennas are parabolic dishes whose cross sectional area can be assumed equal to the effective antenna aperture. a) Calculate the Voyager antenna gain (dB) and diameter b) Calculate the receiver antenna gain (dB) with a dish diameter of 64m. c) Calculate...
Node A is communicating with node B through a link of length 31km with a loss...
Node A is communicating with node B through a link of length 31km with a loss of 4.2 dB/km. Assume the transmitter power at A is 73dBm. If the signal is amplified at 5km by an amplifier and the received signal power at B is 6,111mW. What is the gain of the amplifier in dB?
How much power is received by a radar receiver located 100 km from a jammer with...
How much power is received by a radar receiver located 100 km from a jammer with the fol- lowing characteristics? Assume that the radar antenna has an effective area of 1.2 square meters and that the main beam is pointed in the direction of the jammer. Consider only atmospheric attenuation, excluding the effects of, for example, component loss. Provide the answer in terms of watts and dBm (dB relative to a milliwatt.) Jammer peak power 100 watts Jammer antenna gain...
A small satellite with the following characteristics is directly above the ground station. Assume the following:...
A small satellite with the following characteristics is directly above the ground station. Assume the following: Transmitter output power = 1 Watt Altitude = 10,000 km. Carrier frequency = 0.5 GHz Bandwidth = 20 kHz Antenna gain = 1 dB Data rate = 10 kbps The g A small satellite with the following characteristics is directly above the ground station. Assume the following:       Transmitter output power = 1 Watt       Altitude = 10,000 km.       Carrier frequency = 0.5...
A certain radar, operating at 3 GHz, with an antenna of gain of 40 dB (assumed...
A certain radar, operating at 3 GHz, with an antenna of gain of 40 dB (assumed the same for both transmission and reception) and a peak power of 1MW, can reliably detect a target if the peak power in the returned signal is at least 5 times the system noise power. If the noise power is 10-12 W, estimate the smallest radar cross section the system can detect at 40 km.
A population has a standard deviation σ of 36 units. (Give your answers correct to two...
A population has a standard deviation σ of 36 units. (Give your answers correct to two decimal places.) (a) Find the standard error for the mean (standard deviation of sample mean) if n = 28. (b) Find the standard error for the mean if n = 50. (c) Find the standard error for the mean if n = 85.
PLEASE DRAW THE CIRCUIT DIAGRAMS OF EACH DEFINITIONS AND GIVE ITS APPLICATIONS. PLEASE GIVE THE FULL...
PLEASE DRAW THE CIRCUIT DIAGRAMS OF EACH DEFINITIONS AND GIVE ITS APPLICATIONS. PLEASE GIVE THE FULL DETAILS OF THE STEPS ON EACH QUESTIONS SO I COULD FOLLOW UP YOUR WHOLE EXPLANATIONS. PLEASE WRITE THE STEPS ON SOLVING THIS EXAMPLE EX) STEP 1, STEP 2, ETC HANDWRITING IS OKAY AS LONG AS IT IS READABLE. IF YOU HAVE USED THE EQUATIONS OR CONCEPTS, PLEASE STATE IT CLEARLY WHICH ONE YOU HAVE YOU USED SO I COULD FULLY UNDERSTAND THE DETAILS OF...
Just give the correct answer (no need to explain if you provide an accurate answer) a....
Just give the correct answer (no need to explain if you provide an accurate answer) a. The following input is not needed to solve the option price in the Black-Scholes-Merton framework: the asset’s risk premium the asset price the strike price the risk-free rate of interest b. When volatility is used for____, volatility is the standard deviation of the ____ compounded return per ___. option pricing, continuously, year option pricing, continuously, day risk management, discretely, year risk management, discretely, day...
What is the correct alternative for each question? 1. Suppose there are two inputs for production,...
What is the correct alternative for each question? 1. Suppose there are two inputs for production, labor, and capital. The firm’s production process is defined by the following production function y = f (L, K). How do we interpret the firm’s marginal rate of technical substitution? a) How many units of capital the firm would have to give up in order to attain one more unit of labor, such that the firm maintains the same cost level b) How many...