Question

A highway project has a typical cross section for fill that is crowned at 4% for...

  1. A highway project has a typical cross section for fill that is crowned at 4% for a total top width of 40 feet and then side slopes are 4:1. Compute the X-sectional area of this X-section for a section over level ground that has 4.84 feet of fill at the center line. Also how far is it from the centerline out to the slope stake?
Engineering   Civil-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A water trough is 9 feet long, and its cross section is an equilateral triangle with...
A water trough is 9 feet long, and its cross section is an equilateral triangle with sides 4 feet long. Water is pumped into the trough at a rate of 2 cubic feet per second. How fast is the water level rising when the depth of the water is 1/2 foot? ( Hint: First, what is the height h of an equilateral triangle of side length s? Next, what is the area of an equilateral triangle in terms of the...
A car carrying the infamous G.W. Shrub is driving along a remote section of highway 317...
A car carrying the infamous G.W. Shrub is driving along a remote section of highway 317 (a.k.a. N. Lone Star Parkway) that runs parallel to a 43 m tall cliff just north of Crawford in McLennan County. G.W. is driving a convertible with the top down while you are standing at the top of the cliff with a water balloon launcher that you have experimentally determined has a maximum range of 65 m measured along level ground from the base...
Water flows through two sections of a horizontal tube. The first section has a cross sectional...
Water flows through two sections of a horizontal tube. The first section has a cross sectional area of ​​50 cm ^ 2 and the second section is 10 cm ^ 2. If the velocity of water in the thickest tube is 1.2 m / s and the pressure is 2.20 x 10 ^ 5 Pa, find: a- the speed of the water in the thinnest tube b- the pressure of the water in the thinnest tube
A rectangular open channel (concrete n=0.012) has a slope of 0.12 ft/ft, and a cross sectional...
A rectangular open channel (concrete n=0.012) has a slope of 0.12 ft/ft, and a cross sectional area of 120 square feet. The water is 50 deg F, with a density of 1.94 slugs/ft3, and a dynamic viscosity of 2.73 x 10-5 lbf-s/ft2. If the water surface has 1.0 foot of free board at peak flow of 870.0 cubic feet per second, is the flow laminar or turbulent? (prove with calculations).
A trough is 4 feet long and 11 foot high. The vertical cross-section of the trough...
A trough is 4 feet long and 11 foot high. The vertical cross-section of the trough parallel to an end is shaped like the graph of y=x^8 from x=−1 to x=1. The trough is full of water. Find the amount of work required to empty the trough by pumping the water over the top. Note: The weight of water is 62 pounds per cubic foot. Your answer must include the correct units.
A steel bar has cross-sectional area A=10-3 m2, Young modulus E= 2 x 1011 Pa and...
A steel bar has cross-sectional area A=10-3 m2, Young modulus E= 2 x 1011 Pa and Poisson’s ratio of 0.4. The steel bar has a rectangular cross sectional area. a.         If the bar is subject to a compressive force of 105 N, find the corresponding longitudinal and transverse strains.                                                    [3 marks] b.         Two strain gauges, each with unstrained resistance of 120 Ω and a gauge factor of 2.0 are bonded on to the top surface of the steel bar....
4. A 50-m tape of standard length has a weight of .05kg/m, with a cross-sectional area...
4. A 50-m tape of standard length has a weight of .05kg/m, with a cross-sectional area of 0.04 sq.cm. It has a modulus of elasticity of 2.10x106 kg/sq.cm. The tape is of standard length under a pull of 5.5 kg when supported throughout its length and a temperature of 20°C. This tape was used to measure a distance between A and B and was recorded to be 458.65m. long. At the time of measurement the pull applied was 8 kg....
A wire coil has 1340 turns of copper wire. The cross-section radius is .4 mm. It...
A wire coil has 1340 turns of copper wire. The cross-section radius is .4 mm. It has a diameter of 3.4 cm and a length 8.95 cm. It is oriented along the y-axis. Each end is connected to a 12 V battery.   The temp. is 210C. a)find the length of the wire needed for the coil b)the resistance of the coil c) the magnitude of the magnetic field at a point within the coil d) a +30 uC particle is...
MATH125: Unit 1 Individual Project Answer Form Mathematical Modeling and Problem Solving ALL questions below regarding...
MATH125: Unit 1 Individual Project Answer Form Mathematical Modeling and Problem Solving ALL questions below regarding SENDING A PACKAGE and PAINTING A BEDROOM must be answered. Show ALL step-by-step calculations, round all of your final answers correctly, and include the units of measurement. Submit this modified Answer Form in the Unit 1 IP Submissions area. All commonly used formulas for geometric objects are really mathematical models of the characteristics of physical objects. For example, a basketball, because it is a...
Analysis: This section should include the issue register as a bare minimum, but may include also...
Analysis: This section should include the issue register as a bare minimum, but may include also why-why diagrams, a Pareto chart, a waste table and/or value-added analysis table. Flow analysis or simulation of this case study might be possible but might require making a lot of assumptions given the provided data. The first part of the project: Introduction    Walmart has continued to retain the top position on the Fortune 500 list for a consecutive fifth year. The brand has...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT