Question

I have run Gas Chromatography, NMR spectroscopy, or Distillation to identify the unknown compoments of mixture...

I have run Gas Chromatography, NMR spectroscopy, or Distillation to identify the unknown compoments of mixture and % composition of mixture. But the data contradict to each other and so what could be the reasons for the discrepancy?

Homework Answers

Answer #1

Difference between gas chromatography and fractional distillation is that the fractional distillation is used to separate components on a very large scale whereas gas chromatography technique is applied to very small scale of the oreder of microscale .

Now, the NMR spectroscopy do not depend upon the boiling point of the substrate just like in distillation and gas chromatography but it depends on their magnetic properties that's why there is difference in the obtained values

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A student separated two unknown compounds using Fractional Distillation followed by Gas Chromatography. The GC column...
A student separated two unknown compounds using Fractional Distillation followed by Gas Chromatography. The GC column had a non-polar liquid stationary phase and Helium was the mobile phase. Using the following data, determine the identity, boiling point and percent composition for each of the compounds in the GC sample. Explain reasoning. Your left peak has a percent composition of 20.49% and the right has 79.6%. Hexane boiling pint is 69.2 Heptane boiling boing is 98.5 Methanol is 65.1 Octane 126...
A gas mixture is made by combining 6.1 g each of Ar, Ne, and an unknown...
A gas mixture is made by combining 6.1 g each of Ar, Ne, and an unknown diatomic gas. At STP, the mixture occupies a volume of 12.12 L What is the molar mass of the unknown gas?Identify the unknown gas.
A gas mixture is made by combining 6.16.1 g each of Ar, Ne, and an unknown...
A gas mixture is made by combining 6.16.1 g each of Ar, Ne, and an unknown diatomic gas. At STP, the mixture occupies a volume of 12.1212.12 L. What is the molar mass of the unknown gas? Identify the unknown gas.
Lab Name: Analysis of an Unknown Mixture Using the Ideal Gas Law Purporse: Determine the percent...
Lab Name: Analysis of an Unknown Mixture Using the Ideal Gas Law Purporse: Determine the percent composition by mass of an unknownmixture of sodium nitrite, NaNO2, and sodium chlordie, NaCl, aftercollecting a gas evolved by reaction of NaNO2. Pre-Lab Notes: In this experiment you will react a mixture of sodium nitrite,NaNO2, and sodium chloride, NaCl, of unknown composition with anexcess of sulfamic acid, HSO3NH2. The NaCl is unreactive underthese conditions whereas the NaNO2 reacts to form nitrogen gas byfollowing equation."...
You run a reaction with column chromatography and you find that you have multiple products (cyclohexene...
You run a reaction with column chromatography and you find that you have multiple products (cyclohexene from cyclohexanol). You predictyou have the alcohol functionality you were trying to make and the alkene from the eliminated product (some of the alochol must have elimited to form the alkene). You run a few TLCs to find a good solvent to run a column in order to separate two products. You decide on a 10% ethyl acetate in hexanes because it allows one...
IR spectroscopy question: I have two shorter bumps at 3460 and 3309 cm -1 and I...
IR spectroscopy question: I have two shorter bumps at 3460 and 3309 cm -1 and I know this is supposed to be benzene? the product we were supposed to make in lab was 6-ethoxycarbonyl-3,5-diphenyl-2-cyclohexenone. If you could just go over the major functional groups and an estimation of where the absorptions should be for this molecule so I can compare it to my IR spectrum. Tried to put IR spectrum of my product up but it is blurry like every...
I have a spectrum obtained from an H-NMR. The sample was very dilute in the CDCl3...
I have a spectrum obtained from an H-NMR. The sample was very dilute in the CDCl3 that was used, so the spectrum is very noisy. The sample was scanned multiple times, but there is still a fair amount of noise. I have integrals measured out, but I've realized that some of the peaks that were included when measuring the integrals were not relevant to the compound. Does the inclusion of these peaks detrimentally affect the other integrations? Is there a...
Microbiology, i am a bit confused right now. i have been given an assigment to identify...
Microbiology, i am a bit confused right now. i have been given an assigment to identify a bacteria i am workring with and answer some questions using scholarly sources. the only issue is i am finding it hard to firgure out which source to use as they contradict each other sometimes. The Bacteria is Bacillus Subtilis(well known) I have the following questions, although i have answered them all; i still need clarification and another source. please attach a link to...
Acetylene torches are used for welding. These torches use a mixture of acetylene gas, C2H2, and...
Acetylene torches are used for welding. These torches use a mixture of acetylene gas, C2H2, and oxygen gas, O2 to produce the following combustion reaction: 2C2H2(g)+5O2(g)→4CO2(g)+2H2O(g) Imagine that you have a 5.50 L gas tank and a 4.50 L gas tank. You need to fill one tank with oxygen and the other with acetylene to use in conjunction with your welding torch. If you fill the larger tank with oxygen to a pressure of 115 atm , to what pressure...
Acetylene torches are used for welding. These torches use a mixture of acetylene gas, C2H2, and...
Acetylene torches are used for welding. These torches use a mixture of acetylene gas, C2H2, and oxygen gas, O2 to produce the following combustion reaction: 2C2H2(g)+5O2(g)→4CO2(g)+2H2O(g) Part A Imagine that you have a 7.00 L gas tank and a 2.50 L gas tank. You need to fill one tank with oxygen and the other with acetylene to use in conjunction with your welding torch. If you fill the larger tank with oxygen to a pressure of 155 atm , to...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT