Question

How will the melting point of a beryllium-gold alloy compare to that of pure gold?

How will the melting point of a beryllium-gold alloy compare to that of pure gold?

Homework Answers

Answer #1
The melting point of a pure substance is always higher and has a smaller variation range of the melting point of an impure substance . The more impure it is , the lower the melting point and the wider the range of variation. Eventually, a melting point minimum is reached. The mix ratio which results in the lowest possible point of melting is known as the eutectic point , belonging to each atom temperature of the substance to which it is subjected to fusion .
There are certain specific concentrations of each alloy for which the melting temperature is unified . This concentration and the obtained alloy are called eutectic , and has a melting point lower than the melting points of the components
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Melting Point determination. Compare the sample melting point value that was obtained in the lab (which...
Melting Point determination. Compare the sample melting point value that was obtained in the lab (which was 75-80oC) to the literature value and comment on the range of the melting (according to the literature, pure and solvent free acetanilide melts over a ~ 2 0C range). Compare to the m.p. range and behavior of the original impure acetanilide and explain any difference.
The melting point of gold is known to be approximately 1,060 degrees centigrade. This is, of...
The melting point of gold is known to be approximately 1,060 degrees centigrade. This is, of course, an average figure, for unavoidable ‘experimental error’ causes more or less variation from this figure whenever the test is actually performed. The best measure of these variations is the standard deviation. Suppose this has been calculated from a large series of tests (over 100 trials), and found to be 3 degrees centigrade. Due to the recent increase in the price of gold, special...
1. Is the freezing point and melting point of pure lauric acid the same or different?...
1. Is the freezing point and melting point of pure lauric acid the same or different? Why? 2. How should you dispose of lauric acid/benzoic acid after the experiment is complete? Why? please solve both questions.
Consider 50 gram of gold with initial temperature 27 C. Melting point of gold is 1064...
Consider 50 gram of gold with initial temperature 27 C. Melting point of gold is 1064 C. Find the heat required to melt the gold. Given specific heat of gold is .03 cal/(gram C) , heat of fusion is 15.4 cal/(gram C)
Compute the number of gold atoms per cubic centimeter for a silver-gold alloy that contains 10...
Compute the number of gold atoms per cubic centimeter for a silver-gold alloy that contains 10 wt% Au and 90 wt% Ag. The densities of pure gold and silver are 19.32 and 10.49 g/cm3, respectively.
Red gold is a gold‑copper alloy used to make jewelry. A piece of jewelry made of...
Red gold is a gold‑copper alloy used to make jewelry. A piece of jewelry made of red gold weighs 7.20 g and has a volume of 0.535 cm3. Gold has a density of 19.3 g/cm3 and copper has a density of 8.96 g/cm3. Calculate the percentage by mass of each metal in the jewelry. Assume the total volume of the jewelry is the sum of the volumes of the two metals it contains. gold: % copper: % Pure gold is...
The addition of an impurity to a pure substance will cause its melting point to decrease...
The addition of an impurity to a pure substance will cause its melting point to decrease in proportion to the amount of impurity. Explain this phenomenon.
Red gold is a gold‑copper alloy used to make jewelry. A piece of jewelry made of...
Red gold is a gold‑copper alloy used to make jewelry. A piece of jewelry made of red gold weighs 9.87 g9.87 g and has a volume of 0.559 cm30.559 cm3. Gold has a density of 19.3 g/cm319.3 g/cm3 and copper has a density of 8.96 g/cm38.96 g/cm3. Calculate the percentage by mass of each metal in the jewelry. Assume the total volume of the jewelry is the sum of the volumes of the two metals it contains. gold: % copper:...
An aluminum alloy is to be strengthened by the incorporation of beryllium oxide (BeO) particles. Calculate...
An aluminum alloy is to be strengthened by the incorporation of beryllium oxide (BeO) particles. Calculate the (a) upper and (b) the lower bound elastic moduli of a composite consisting of 40% alloy and 60% wt% BeO. Young’s modulus of the alloy is 70.3 GPa and its density is 2698 kg/m3. Young’s modulus of BeO is 301.3 GPa and its density is 3010 kg/m3.
Red gold is a gold‑copper alloy used to make jewelry. A piece of jewelry made of...
Red gold is a gold‑copper alloy used to make jewelry. A piece of jewelry made of red gold weighs 7.03 g7.03 g and has a volume of 0.483 cm30.483 cm3. Gold has a density of 19.3 g/cm319.3 g/cm3 and copper has a density of 8.96 g/cm38.96 g/cm3. Calculate the percentage by mass of each metal in the jewelry. Assume the total volume of the jewelry is the sum of the volumes of the two metals it contains. A) What is...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT