Question
There is a test tube which contains 3mL of 0.1 M CuSO4, add a piece of...
There is a test tube which contains 3mL of 0.1 M CuSO4, add a
piece of mossy zinc. What is the balanced equation and reaction
type? Please explain and show steps.
Homework Answers
Answer #1
Not the answer you're looking for?
Similar Questions
you pour too much 0.1 m NH3/H20 solution into test tube #1 & #2, leaving only...
you pour too much 0.1 m NH3/H20 solution into test
tube #1 & #2, leaving only 1 mg of the solution in test tube
#3. you add phenolphtalein indicator solution as directed.
You have a solution that contains 0.1 M Ag+ , 0.1 M Cu2+ and 0.1 M...
You have a solution that contains 0.1 M Ag+ , 0.1 M Cu2+ and 0.1
M Ba2+. You would like to separate these ions by precipitation. For
quality purposes, the relative error must be below 0.1%, i.e., the
precipitation of each ion must be complete (>99.9%) and there
must not be more than 0.1% (by weight) of one of the other ions in
the precipitate. Explain your answer: nature of precipitate, pH,
concentrations etc. Be quantitative in your answer. Note:...
A piece of zinc reacts with hydrochloric acid to form zinc chloride and hydrogen gas, which...
A piece of zinc reacts with hydrochloric acid to form zinc
chloride and hydrogen gas, which is collected over water at 150 C
into a large flask. The total pressure is adjusted to 1.00 bar, and
the volume is 1495 mL
(a) What is the PH2? (ANSWER = 0.98 bar)
(b) What is the mass of H2? (ANSWER = 0.12 g)
(c) What mass of Zn was used in this process? (ANSWER = 4.0
g
please show me the steps>>>>
Chemical Equilibrium: Le Chatelier’s Principle. 1. Add 0.5 mL of 0.1 M FeCl3(aq) to 0.5 mL...
Chemical Equilibrium: Le Chatelier’s Principle.
1. Add 0.5 mL of 0.1 M FeCl3(aq) to 0.5 mL of 0.1 M KSCN(aq),
and then add 15 mL of distilled water. To a 2-mL portion of this
mixture, add 1 mL of 0.1 M KSCN(aq). Observe any difference in the
color from the original solution and explain your observations.
Because you are combining equal volumes of equal concentrations,
and because they combine in a 1 to 6 mole ratio, Fe3+(aq) should be
in...
Procedure Reaction 1: Dissolving the Copper 1. Obtain a clean, dry, glass centrifuge tube. 2. Place...
Procedure Reaction 1: Dissolving the Copper 1. Obtain a clean,
dry, glass centrifuge tube. 2. Place a piece of copper wire in a
weighing paper, determine the mass of the wire and place it in the
centrifuge tube. The copper wire should weigh less than 0.0200
grams. 3. In a fume hood, add seven drops of concentrated nitric
acid to the reaction tube so that the copper metal dissolves
completely. Describe your observations in the lab report. (Caution,
Concentrated nitric...
You need to prepare a phosphoric acid buffer that has a buffer concentration of 0.1 M,...
You need to prepare a phosphoric acid buffer that has a buffer
concentration of 0.1 M, a pH of 6.65, and taking in to account
activity. First, ignoring ativiy, calculate [A-] and [HA] needed to
prepare the buffer using the Henderson-Hasselbalch equation and the
fact that [buffer]=0.1 M. (Hint: you have two equations and two
unknowns). (pKa1=2.15, pKa2=7.09, pKa3=12.32)
Please show your work and explain your steps.
The chemical reactions that are used in the anion spot tests in this experiment are for...
The chemical reactions that are used in the anion spot tests in
this experiment are for the most part precipitation or acid-base
reactions.Given the information in each test procedure, try to
write the net ionic equation for the key reaction in each test.
NO3- (Take Al and NO3- to be
the reactants, and NH3 and
Al(OH)4-to be the products; the final
reaction also contains OH- and H2O as
reactants): To 1 mL 0.5 m NaNO3 add 1 mL 6M NaOH....
1.Use a permanent marker to label three test tubes "Carbonate Ion Test," "Sulfate Ion Test" and...
1.Use a permanent marker to label three test tubes "Carbonate
Ion Test," "Sulfate Ion Test" and "Phosphate Ion Test.
2.Use the 10 mL graduated cylinder to measure and pour 2 mL of
the unknown solution into each test tube.
3.Perform the Carbonate Ion Test by pipetting five drops of
acetic acid into the test tube labeled "Carbonate Ion Test
4.Perform the Sulfate Ion Test by pipetting one drop of acetic
acid (using the pipette from Step 5) and four drops...
Experiment 1: Observe the Reactions Between Halide and Calcium Ions Take four test tubes from the...
Experiment 1: Observe the Reactions Between Halide and
Calcium Ions
Take four test tubes from the Containers shelf and place them on
the workbench.
Fill each test tube with a different halide solution from the
Materials shelf, as directed below. You may want to label the test
tubes by double-clicking on each test tube and renaming it.
Test Tube #
Halide Solution
1
10.5 mL 0.1 M sodium chloride
2
10.5 mL 0.1 M sodium fluoride
3
10.5 mL 0.1...
Anyone that is willing to give this a shot is much appreciated since i understand that...
Anyone that is willing to give this a shot is much appreciated
since i understand that this takes a minutes with the multiple
parts to each question, but with that said I have a test tomorrow
and this is what i understand the least off of it I have my own
answers to this portion of the study guide but need something to
compare them to. PLEASE take your time and be as descriptive as you
can be, it is...
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 36 minutes ago
asked 40 minutes ago
asked 40 minutes ago
asked 48 minutes ago
asked 48 minutes ago
asked 49 minutes ago
asked 56 minutes ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago