Question
You want to build a control chart constant table for a false alarm rate of 600,...
You
want to build a control chart constant table for a false alarm rate
of 600, what will be the value of the constant to build a control
chart for the standard deviation of the sample size of 15?
Homework Answers
Answer #1
The question asked about to find Table constant to build a Standard Deviation chart ( S chart ) of sample size 15.
A detailed explanation to obtain this constant is given as handwritten images. Hope it will satisfies you. If you are satisfied please Thumbs Up.. Thanks inadvance for your support dear...
Not the answer you're looking for?
Similar Questions
1 An x̅ chart with a sample size of 4 is used to control the mean...
1
An x̅ chart with a sample size of 4 is used to control the mean
of a normally distributed quality characteristic. It is known that
process standard deviation is 8. The upper and lower control limits
of the chart are 147 and 123 respectively. Assume the process mean
shifts to 121.
What is the probability that this shift is detected on the first
subsequent sample?
What is expected number of samples taken before the shift is
detected?
2
The...
A control chart for fraction nonconforming indicates that the current process average is 0.03. The sample...
A control chart for fraction nonconforming indicates that the
current process average is 0.03. The sample size is constant at 200
units. a) Find the three-sigma control limits for the control
chart. b) What is the probability that a shift in the process
average to 0.08 will be detected on the first subsequent sample?
(Hint: use normal approximation) c) What is the probability that
this shift will be detected on the second sample taken after the
shift?
You want to estimate the average of a population, for these a sample of size 21...
You want to estimate the average of a population, for these a
sample of size 21 was taken, and the average and variance of the
sample were calculated. These are 10.52 and 3.25
respectively.
a. Build a confidence interval for the average, if 90 percent
confidence is desired. (15 pts)
b. Calculate the sample size if you want the relative error to be
10 percent with a reliability of 95 percent. (15 pts)
A quality manager asked his team to implement p control chart for a process that was...
A quality manager asked his team to implement p control chart
for a process that was recently introduced. The team collected
samples of size n = 100 parts hourly over a period of 30 hours and
determined the proportion of nonconforming parts for each sample.
The mean proportion of nonconforming parts for 30 samples turned
out to be 0.025.
Determine the upper and lower control limits for the p chart.
(2 Points)
Discuss how you will use the p Chart...
A fraction nonconforming control chart with n = 400 has the following parameters: UCL = 0.0962,...
A fraction nonconforming control chart with n = 400 has the
following parameters: UCL = 0.0962, Center line = 0.0500, LCL =
0.0038
a. Find the width of the control limits in standard deviation
units.
b. Suppose the process fraction nonconforming shifts to 0.15.
What is the probability of detecting the shift on the first
subsequent sample?
You want to build up an annuity which can pay you $5,000 per month for 25...
You want to build up an annuity which can pay you $5,000 per
month for 25 years (= 300 months), when the monthly interest rate
is .006 per month. You want the annuity to begin paying you after
15 years (= 180 months) of saving at an interest rate of .005. What
must your monthly level of saving be, in order to carry out this
plan?
a. $2389.26
b. $2856.91
c. $3417.96
d. None of these
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following
table:
SAMPLE
n
NUMBER OF DEFECTIVE ITEMS IN THE SAMPLE
1
15
1
2
15
1
3
15
3
4
15
1
5
15
0
6
15
0
7
15
2
8
15
1
9
15
2
10
15
1
a. Determine the p−p− , Sp,
UCL and...
Assume that you want to test the hypothesis that the mean weight of the male student...
Assume that you want to test the hypothesis that the mean weight
of the male student population is 160 lbs.
If we assume that the standard deviation has a known value of 12
lbs and we want to test with a confidence level of 95%
a. What sample size should we use if we want one to have a
probability of making a type II error of no more than 5% in the
test when the actual mean is 162...
You are the CEO at a nail polish manufacturing plant. You want to determine if the...
You are the CEO at a nail polish manufacturing plant.
You want to determine if the nail polish filling process is in
control. The process requires NO corrective action if the correct
amount of nail polish is 368 grams. For studying this, a random
sample of 25boxes, weighing each one. The sample mean is 372.5 and
the process standard deviation (population) is 15. Is there
evidence that the weight is different from 368 grams? You have
selected α = 0.01...
You want to use the dividend discount model with a constant growth rate to value security....
You want to use the dividend discount model with a
constant growth rate to value security. What is the most difficult
input to estimate correctly? Why? Does getting this input wrong
give significant consequences? Explain.
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 4 minutes ago
asked 16 minutes ago
asked 20 minutes ago
asked 23 minutes ago
asked 26 minutes ago
asked 30 minutes ago
asked 35 minutes ago
asked 57 minutes ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 2 hours ago