Question
Twenty-five samples of 100 items each were inspected when a process was considered to be operating...
Twenty-five samples of 100 items each were inspected when a process was considered to be operating satisfactorily. In the 25 samples, a total of 185 items were found to be defective.
(a)
What is an estimate of the proportion defective when the process is in control?
(b)
What is the standard error of the proportion if samples of size 100 will be used for statistical process control? (Round your answer to four decimal places.)
(c)
Compute the upper and lower control limits for the control chart. (Round your answers to four decimal places.)
UCL=LCL=
Homework Answers
Answer #1
Not the answer you're looking for?
Similar Questions
Twenty-five samples of 100 items each were inspected when a process was considered to be operating...
Twenty-five samples of 100 items each were inspected when a
process was considered to be operating satisfactorily. In the 25
samples, a total of 180 items were found to be defective.
(a)What is an estimate of the proportion defective when the
process is in control?
_________________.
(b)What is the standard error of the proportion if samples of
size 100 will be used for statistical process control? (Round your
answer to four decimal places.)
________________.
(c)Compute the upper and lower control...
Twelve samples, each containing five parts, were taken from a process that produces steel rods at...
Twelve samples, each containing five parts, were taken from a
process that produces steel rods at Emmanual Kodzi's factory. The
length of each rod in the samples was determined. The results were
tabulated and sample means and ranges were computed.
Refer to Table S6.1 - Factors for computing control chart limits
(3 sigma) for this problem.
Sample
Size, n
Mean Factor,
A2
Upper Range,
D4
Lower Range,
D3
2
1.880
3.268
0
3
1.023
2.574
0
4
0.729
2.282
0...
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following table:
SAMPLE
n
NUMBER OF
DEFECTIVE ITEMS IN THE SAMPLE
1
15
0
2
15
2
3
15
0
4
15
3
5
15
1
6
15
3
7
15
1
8
15
0
9
15
0
10
15
0
a.
Determine the p−p−, Sp, UCL and LCL...
A process sampled 20 times with a sample of size 8 resulted in = 23.5 and R...
A process sampled 20 times with a sample of size 8 resulted
in = 23.5 and R = 1.8.
Compute the upper and lower control limits for the x chart for
this process. (Round your answers to two decimal places.)
UCL=________.
LCL=________.
Compute the upper and lower control limits for the R
chart for this process. (Round your answers to two decimal
places.)
UCL=_________.
LCL=___________.
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following
table:
SAMPLE
n
NUMBER OF DEFECTIVE ITEMS IN THE SAMPLE
1
15
1
2
15
1
3
15
3
4
15
1
5
15
0
6
15
0
7
15
2
8
15
1
9
15
2
10
15
1
a. Determine the p−p− , Sp,
UCL and...
Twenty-five samples, each consisting of 150 loan applications at a bank resulted in a total of...
Twenty-five samples, each consisting of 150 loan applications at
a bank resulted in a total of 22 applications that had some type of
error.
Round your answer to 5 digits after the decimal point if
it is not an integer. Do NOT use comma in your numeric
answers.
Sample size is ______
Number of samples is .________
When constructing a p chart the center line should be
.________
ESD(p) equals ._______
The upper control limit (UCL) should be .________
The...
A manufacturing process produces steel rods in batches of 2,200. The firm believes that the percent...
A manufacturing process produces steel rods in batches of 2,200.
The firm believes that the percent of defective items generated by
this process is 4.3%.
a. Calculate the centerline, the upper control
limit (UCL), and the lower control limit (LCL) for the p¯p¯ chart.
(Round your answers to 3 decimal places.)
centerline-
Upper control limit-
Lower control limit-
b. An engineer inspects the next batch of 2,200
steel rods and finds that 5.5% are defective. Is the manufacturing
process under...
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following table:
SAMPLE
n
NUMBER OF
DEFECTIVE ITEMS IN THE SAMPLE
1
15
0
2
15
0
3
15
0
4
15
2
5
15
0
6
15
3
7
15
1
8
15
0
9
15
3
10
15
1
a.
Determine the p−p−, Sp, UCL and LCL...
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following
table:
SAMPLE
n
NUMBER OF DEFECTIVE ITEMS IN THE SAMPLE
1
15
2
2
15
2
3
15
2
4
15
0
5
15
2
6
15
1
7
15
3
8
15
2
9
15
1
10
15
3
a. Determine the p−p− , Sp,
UCL and...
A manufacturing process produces steel rods in batches of 1,700. The firm believes that the percent...
A manufacturing process produces steel rods in batches of 1,700.
The firm believes that the percent of defective items generated by
this process is 5.4%. a. Calculate the centerline, the upper
control limit (UCL), and the lower control limit (LCL) for the p⎯⎯
chart. (Round your answers to 3 decimal places.) b. An engineer
inspects the next batch of 1,700 steel rods and finds that 6.5% are
defective. Is the manufacturing process under control?
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 19 minutes ago
asked 21 minutes ago
asked 32 minutes ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 2 hours ago