Question
During the process of producing toilet paper, Scott Paper randomly selects a toilet paper roll 5...
|
During the process of producing toilet paper, Scott Paper randomly selects a toilet paper roll 5 times throughout the day and subjects each roll to a stress test to see how often the paper tears. Over a 3-day period, the testing of 15 rolls found the following number of defectives in each roll: 2, 3, 1, 2, 3, 2, 3, 3, 1, 2, 2, 1, 2, 2 and 1. |
|
Construct a control chart for the process. (Leave no cells blank - be certain to enter "0" wherever required. Round your answers to 2 decimal places.) |
| Limits on the control chart are from ______ to _______ tears. |
Homework Answers
Answer #1
Not the answer you're looking for?
Similar Questions
Scott Paper tests its toilet paper by subjecting 15 rolls to a wet stress test to...
Scott Paper tests its toilet paper by subjecting 15 rolls to a
wet stress test to see whether and how
often the paper tears during the test. Following are the number of
defectives found over the last 15
days: 2, 3, 1, 2, 2, 1, 3, 2, 2, 1, 2, 2, 1, 0, and 0.
1. Calculate the CL, UCL, and LCL.
2. Construct a control chart for the process and comment on whether
the process is \in control."
Scott is deciding which type of toilet paper to buy. There are two varieties of toilet...
Scott is deciding which type of toilet paper to buy. There are
two varieties of toilet paper- a regular size (R) and a jumbo size
(J) that has four times as many sheets per roll. Assume that
Scott’s preferences for the two varieties can be expressed by the
utility function U=1/4 R+J. (4 points each) Graph Scott’s
indifference curves for U = 1 and U = 2 with R on the x-axis. What
is Scott’s marginal rate of substitution of...
A shirt manufacturer buys cloth by the 100 yard roll from a supplier. For setting up...
A shirt manufacturer buys cloth by the 100 yard roll from a
supplier. For setting up a control chart to manage the
irregularities (e.g., loose threads and tears) the following data
was collected from a sample provided by the supplier.
SAMPLE
1
2
3
4
5
6
7
8
9
10
IRREGULARITIES
1
4
1
4
3
2
3
5
6
4
a. Determine the c¯c¯ , Sp,
UCL and LCL for a c -chart with z= 2.
(Leave no...
If you drop two rolls of toilet paper, while holding onto the end of one roll...
If you drop two rolls of toilet paper, while holding onto the
end of one roll (meaning, one unrolls as it falls, the other drops
straight down), they will land at the same time if the initial
heights have a specific ratio. Each roll has an inner diameter of
3.5cm and an outer diameter of 11cm.
1. For the roll that you hold onto the end of (the one that
unrolls), how fast would it hit the ground if you...
If you drop two rolls of toilet paper, while holding onto the end of one roll...
If you drop two rolls of toilet paper, while holding onto the
end of one roll
(meaning, one unrolls as it falls, the other drops straight
down), they will land
at the same time if the initial heights have a specific ratio.
Each roll has an
inner diameter of 3.5cm and an outer diameter of 11cm.
1. For the roll that you hold onto the end of (the one that
unrolls), how fast
would it hit the ground if you...
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following
table:
SAMPLE
n
NUMBER OF DEFECTIVE ITEMS IN THE SAMPLE
1
15
1
2
15
1
3
15
3
4
15
1
5
15
0
6
15
0
7
15
2
8
15
1
9
15
2
10
15
1
a. Determine the p−p− , Sp,
UCL and...
A bicycle manufacturer randomly selects 8 frames each day and tests for defects. The number of...
A bicycle manufacturer randomly selects 8 frames each day and
tests for defects. The number of defective frames found over the
last 14 days is 0, 2, 0, 3, 4, 4, 3, 0, 2, 2, 2, 1, 4, 2.
A.) Determine the control limits for the process. (round to 1
decimal place)
The control limits are from _________ to___________.
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following table:
SAMPLE
n
NUMBER OF
DEFECTIVE ITEMS IN THE SAMPLE
1
15
0
2
15
2
3
15
0
4
15
3
5
15
1
6
15
3
7
15
1
8
15
0
9
15
0
10
15
0
a.
Determine the p−p−, Sp, UCL and LCL...
Ten samples of 15 parts each were taken from an ongoing process to establish a p-chart...
Ten samples of 15 parts each were taken from an ongoing process
to establish a p-chart for control. The samples and the
number of defectives in each are shown in the following table:
SAMPLE
n
NUMBER OF
DEFECTIVE ITEMS IN THE SAMPLE
1
15
0
2
15
0
3
15
0
4
15
2
5
15
0
6
15
3
7
15
1
8
15
0
9
15
3
10
15
1
a.
Determine the p−p−, Sp, UCL and LCL...
Edit question The results of inspection of samples of a product taken over the past 5...
Edit question
The results of inspection of samples of a product taken over the
past 5 days are given below. Sample size for each day has been
100:
Day 1
2
3
4
5
Defectives
2
6
14 3
7
Determine the UCL for this chart
Determine the LCL for this chart
Is this process in control?
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 1 minute ago
asked 3 minutes ago
asked 6 minutes ago
asked 9 minutes ago
asked 9 minutes ago
asked 37 minutes ago
asked 49 minutes ago
asked 50 minutes ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago
asked 1 hour ago