Question

A machine has a speed of 135 rpm and the inertia of the rotating parts is...

A machine has a speed of 135 rpm and the inertia of the rotating parts is 35 kg · m2

a) How much energy is released, the speed is reduced by 15%?

b) How much braking constant torque
needed to get the machine to stop at its original speed of 2.0 minutes? (Answer 970 J; 4.1
nm)

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Please rate it

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A 3-phase 50Hz 2-pole 440V (L-L rms) induction motor drive has a rated speed of 2955...
A 3-phase 50Hz 2-pole 440V (L-L rms) induction motor drive has a rated speed of 2955 rpm and rated torque of 35 Nm. This motor drives a load with a torque characteristic that increases linearly with speed such that it equals the load torque at the rated speed. It draws a current of 3.0 A(rms) per phase at the rated voltage at a power factor of 0.81 (lagging). The stator resistance Rs = {r_s} ohms. At the rated operating speed,...
A car's wheel has a rotational inertia of 3.1 kg m2. Working in a coordinate system...
A car's wheel has a rotational inertia of 3.1 kg m2. Working in a coordinate system where counterclockwise is positive, answer the following questions. Treat parts a, b, and c as stand-alone questions; the response from one is not needed for the following parts. a) If the wheel is spinning with an angular velocity of 6 rad/s counterclockwise and then a torque of 15 N m is applied over a time interval of 4 s, What is the wheel's final...
A car's wheel has a rotational inertia of 2.8 kg m2. Working in a coordinate system...
A car's wheel has a rotational inertia of 2.8 kg m2. Working in a coordinate system where counterclockwise is positive, answer the following questions. Treat parts a, b, and c as stand-alone questions; the response from one is not needed for the following parts. a) If the wheel is spinning with an angular velocity of 6 rad/s counterclockwise and then a torque of 15 N m is applied over a time interval of 4 s, What is the wheel's final...
1) A torque of 1.20 N m is applied to a thin rod of mass 2.50...
1) A torque of 1.20 N m is applied to a thin rod of mass 2.50 kg and length 50.0 cm pivoted about its center and at rest. How fast is the rod spinning after 4.25 s? a. 32.6 rad/s b. 8.16 rad/s c. 97.9 rad/s d. 24.5 rad/s 2) A torque of 1.20 N m is applied to a thin rod of mass 2.50 kg and length 50.0 cm pivoted about one end and at rest. How fast is...
Large objects have inertia and tend to keep moving-Newton's first law. Life is very different for...
Large objects have inertia and tend to keep moving-Newton's first law. Life is very different for small microorganisms that swim through water. For them, drag forces are so large that they instantly stop, without coasting, if they cease their swimming motion. To swim at constant speed, they must exert a constant propulsion force by rotating corkscrew-like flagella or beating hair-like cilia. The quadratic model of drag given by the equation, D⃗  = (12CρAv2, direction opposite the motion), fails for very small...
21) A person carries a 25.0-N rock through the path shown in the figure, starting at...
21) A person carries a 25.0-N rock through the path shown in the figure, starting at point A and ending at point B. The total time from A to B is 1.50 min. How much work did gravity do on the rock between A and B? A) 625 J B) 20.0 J C) 275 J D) 75 J E) 0 J 22) A person carries a 2.00-N pebble through the path shown in the figure, starting at point A and...
How can differential analysis be applied here to determine if it would be profitable to invest...
How can differential analysis be applied here to determine if it would be profitable to invest in new equipment to increase capacity for a constrained resource? KRAYDEN’S CYCLE COMPONENTS INTRODUCTION: COMPANY, PRODUCT, AND SUPPLY CHAIN Krayden’s Cycle Components (KCC) is a high-end specialty fabricator that manufactures one product with many variants. The basic product is known as a rolling chassis, a key component used in manufacturing motorcycles. While there are variations across the industry, a rolling chassis typically consists of...
What tools could AA leaders have used to increase their awareness of internal and external issues?...
What tools could AA leaders have used to increase their awareness of internal and external issues? ???ALASKA AIRLINES: NAVIGATING CHANGE In the autumn of 2007, Alaska Airlines executives adjourned at the end of a long and stressful day in the midst of a multi-day strategic planning session. Most headed outside to relax, unwind and enjoy a bonfire on the shore of Semiahmoo Spit, outside the meeting venue in Blaine, a seaport town in northwest Washington state. Meanwhile, several members of...
1. The failure of the new supply chain system affected Nike adversely. What were the reasons...
1. The failure of the new supply chain system affected Nike adversely. What were the reasons for the failure and how did the breakdown harm Nike? 2. What are the important elements to be kept in mind while implementing a new system in an organization? What is the importance of a good working relationship between partners and the sharing of responsibility in implementing critical projects? What mistakes did Nike and i2 make? 3. comment on the lessons learned and the...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT