Question

A closed and elevated vertical cylindrical tank with diameter 80 cm contains water to a depth of 0.900 m . A worker opens a circular hole with diameter 12 cm in the bottom of the tank. As the water drains from the tank, compressed air above the water in the tank maintains a gauge pressure of 5.00×103Pa at the surface of the water. Ignore any effects of viscosity ( ½w = 1000 kg=m3 ).

a) (12 points) Just after the hole is made, what is the speed of the water as it emerges from the hole?

Answer #1

A closed and elevated vertical cylindrical tank with diameter
2.20 m contains water to a depth of 0.900 m . A worker accidently
pokes a circular hole with diameter 0.0180 m in the bottom of the
tank. As the water drains from the tank, compressed air above the
water in the tank maintains a gauge pressure of 5.00×103Pa at the
surface of the water. Ignore any effects of viscosity.
Part A
Just after the hole is made, what is the...

A closed and elevated vertical cylindrical tank with diameter
1.40 m contains water to a depth of 0.800 m . A worker accidently
pokes a circular hole with diameter 0.0140 m in the bottom of the
tank. As the water drains from the tank, compressed air above the
water in the tank maintains a gauge pressure of 5.00×103Pa at the
surface of the water. Ignore any effects of viscosity.
Questions
1. How much time does it take for all the...

A cylindrical tank with a large diameter is filled with water to
a depth D = 0.405 m. A hole of cross-sectional area A = 5.62 cm^2
in the bottom of the tank allows water to drain out. (a) What is
the rate at which water flows out, in cubic meters per second? (b)
At what distance below the bottom of the tank is the
cross-sectional area of the stream equal to one-half the area of
the hole?

A closed cylindrical tank 75 cm in diameter and 1.80
meters high is filled with oil (s = 0.80) such that the top cover
is under a pressure of 24 kPa. When rotated about its vertical axis
at the rate of 240 rpm, determine the force on:
a. The top cover.
b. The bottom.
c. Find the maximum pressure

A large cylindrical tank containing water to a level of 5.00 m
above the bottom of the tank is elevated such that the bottom of
the tank is 5.00 m off the ground. A hose with a length of 3.00 m
and a radius of 1.50 cm is attached to the bottom of the tank and
allowed to hang vertically down. Water begins to drain out from the
end of the hose. The density of water is 1000 kg/m3.
(a)...

A cylindrical bucket, open at the top, is 24.0 cm high and 13.0
cm in diameter. A circular hole with a cross-sectional area 1.50
cm2 is cut in the center of the bottom of the bucket. Water flows
into the bucket from a tube above it at the rate of
2.40×10−4 m3/s . How high will the water in the bucket
rise?

A cylindrical bucket, open at the top, is 24.0 cm high and 12.0
cm in diameter. A circular hole with a cross-sectional area 1.39
cm^2 is cut in the center of the bottom of the bucket. Water flows
into the bucket from a tube above it at the rate of 2.39×10−4 m^3/s
.
How high will the water in the bucket rise?

(a) A large, open at the top, upright cylindrical tank contains
fuel oil with a density of 0.890 ✕ 103 kg/m3.
If the air pressure is 101.3 kPa, determine the absolute pressure
(in Pa) in the fluid at a depth of 22.5 m. ____ pa
(b)Determine the force (in N) exerted by only the fluid on the
window of an instrument probe at this depth if the window is
circular and has a diameter of 3.70 cm.
N

A steel hot-water tank of cylindrical shape has an inside
diameter of 0.600 m and inside height of 1.40 m. The tank is
enclosed by a 5.00 cm thick insulating layer of glass wool whose
thermal conductivity is 0.0350 W / (m·K). The insulation is covered
by a thin sheet metal skin. The steel tank and the sheet metal skin
have thermal conductivities that are much greater than that of the
glass wool. How much electrical power (W) must be...

A large diameter closed top tank is filled with a depth of 3
meters of a fluid (density 1200 kg/m3). A small pipe leading from
the bottom of the tank must carry the fluid some height above the
fluid level in the tank. a) If a pressure of 2.5 Atmospheres is
maintained in the space above the fill line in the tank how high
above the fill line can the pipe carry the fluid and still provide
an exit speed...

ADVERTISEMENT

Get Answers For Free

Most questions answered within 1 hours.

ADVERTISEMENT

asked 8 minutes ago

asked 28 minutes ago

asked 39 minutes ago

asked 40 minutes ago

asked 40 minutes ago

asked 44 minutes ago

asked 48 minutes ago

asked 53 minutes ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago

asked 1 hour ago