Question

calculate the magnetic induction for a solenoid at point located a) in the axis ، at...

calculate the magnetic induction for a solenoid at point located

a) in the axis ، at 25cm from the center with draw

b) at the edge with draw

c) at the center with draw

knowing that the Length of solenoid is 80cm and it's radius 4cm and the turns is 150 turn/m and the current passing through it 6A

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. A long solenoid with 500 turns of wire, length L=80cm and diameter d=2.5cm. The center...
1. A long solenoid with 500 turns of wire, length L=80cm and diameter d=2.5cm. The center of the solenoid is surrounded by a circular loop of wire with a diameter dloop=5.0cm and a resistance R=0.50ohm. The axis of the solenoid is also the axis for the loop. a. What is the magnetic field inside the solenoid when a current of 2.0A passes through the solenoid? [note: the magnetic field inside the solenoid is uniform and there is no magnetic field...
The magnetic field measured with a Teslameter (or Gaussmeter) at the center of a solenoid is...
The magnetic field measured with a Teslameter (or Gaussmeter) at the center of a solenoid is 3.0 mT when a current of 0.3 A is flowing through it. The length of the solenoid is 15.0 cm. (a) Calculate the number of turns in the solenoid. (b) To produce magnetic field of 1.5 T at the center of the solenoid, how much current is needed? (c) If the diameter of the solenoid is 5.0 cm and a 10-turn coil with average...
1- A solenoid with ( turn ) 1000 N connected with each side by galvanometer has...
1- A solenoid with ( turn ) 1000 N connected with each side by galvanometer has resistance 4 Ohm , the solenoid was placed vertically inside a magnetic flux has 0.005 weber . Calculate the average intensity of current induction that passing through the galvanometer if the magnetic flux increased to 0.0075 weber in 0.25 second knowing that the resistance of solenoid is 6 Ohm 2- A solenoid with ( Turn ) 100 N has placed vertically into a stable...
Calculate the magnetic induction at the center of a circular coil having 100 turns of radius...
Calculate the magnetic induction at the center of a circular coil having 100 turns of radius 10 cm which is carrying a current of 5 A
A solenoid has an induction magnet of 12 π x 10-7 T. If the length of...
A solenoid has an induction magnet of 12 π x 10-7 T. If the length of the solenoid 5 m, and the current flowing 1.5 A. Calculate the number of turns of the solenoid and what is the induction of the solenoid magnet at the end of the solenoid?
The strength of the magnetic field within a solenoid is B = 2.1 × 10-2 T...
The strength of the magnetic field within a solenoid is B = 2.1 × 10-2 T (outside the solenoid B = 0). A smaller, single loop is placed in the solenoid parallel to the plane of each loop in the solenoid. The resistance of the solenoid is 5.9 W, the resistance of the loop is 0.27 W, the diameter of the solenoid is 0.09 m, and the diameter of the loop is 0.05 m. An emf of 12 V is...
A 310 turn solenoid with a length of 23.0 cm and a radius of 1.60 cm...
A 310 turn solenoid with a length of 23.0 cm and a radius of 1.60 cm carries a current of 1.85 A. A second coil of four turns is wrapped tightly around this solenoid, so it can be considered to have the same radius as the solenoid. The current in the 310 turn solenoid increases steadily to 5.00 A in 0.900 s. (a) Use Ampere's law to calculate the initial magnetic field in the middle of the 310 turn solenoid....
A long solenoid has 1200 turns, a length of 20cm, and a radius of 10cm, and...
A long solenoid has 1200 turns, a length of 20cm, and a radius of 10cm, and produces a magnetic field when current is run through it. If a proton is fired into the solenoid at a velocity of 50 nm/s in such a way that its velocity is perpendicular to the magnetic field produced by the solenoid, what current needs to be run through the solenoid so that the proton begins orbiting around the center of the solenoid at a...
A single-turn square loop of side L is centered on the axis of a long solenoid....
A single-turn square loop of side L is centered on the axis of a long solenoid. In addition, the plane of the square loop is perpendicular to the axis of the solenoid. The solenoid has 1210 turns per meter and a diameter of 6.25 cm , and carries a current of 3.00 A . Find the magnetic flux through the Loop when L= a)2.70 b)6.25 c)14.0
A solenoid is designed to produce a magnetic field of 0.0570 T at its center. It...
A solenoid is designed to produce a magnetic field of 0.0570 T at its center. It has a radius of 1.50 cm and a length of 30.0 cm, and the wire can conduct a maximum current of 15.0 A. (a) What is the minimum number of turns per unit length that the solenoid must have? (b) What is the total length of wire required?