Question

A hydraulic lift has pistons with diameters 8.00 cm and 36.0 cm, respectively. If a force...

A hydraulic lift has pistons with diameters 8.00 cm and 36.0 cm, respectively. If a force of 825 N is exerted at the input piston, what maximum mass can be lifted by the output piston?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A hydraulic lift has pistons with diameters 7.95 cm and 35.9 cm, respectively. If a force...
A hydraulic lift has pistons with diameters 7.95 cm and 35.9 cm, respectively. If a force of 825 N is exerted at the input piston, what maximum mass can be lifted at the output piston?
2.A hydraulic car lift has an input piston of radius 6.20 cm and negligible weight. The...
2.A hydraulic car lift has an input piston of radius 6.20 cm and negligible weight. The output piston has a radius of 86.9cm. If the total load on the output plungers needs to be 12,000 N. What is the mechanical advantage of the hydraulic system input? 3. A hydraulic car lift has an input piston of radius 4.80 cm and negligible weight. The output piston has a radius of 101 cm. If the total load on the output plungers needs...
The fine piston of a hydraulic jack has a diameter of 1.30 cm. With an applied...
The fine piston of a hydraulic jack has a diameter of 1.30 cm. With an applied force of only 23 N it was possible to lift a weight of 1850 N. Assuming that both pistons are circular, what is the diameter of the wide working piston for this hydraulic jack?
The hydraulic oil in a car lift has a density of 8.73 x 102 kg/m3. The...
The hydraulic oil in a car lift has a density of 8.73 x 102 kg/m3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 8.10 x 10-3 m and 0.101 m, respectively. What input force F is needed to support the 24000-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface...
The hydraulic oil in a car lift has a density of 8.04 x 102 kg/m3. The...
The hydraulic oil in a car lift has a density of 8.04 x 102 kg/m3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 7.63 x 10-3 m and 0.158 m, respectively. What input force F is needed to support the 26400-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface...
A hydraulic lift has 2 connected pistons with cross-sectional areas 20 cm2 and 680 cm2. It...
A hydraulic lift has 2 connected pistons with cross-sectional areas 20 cm2 and 680 cm2. It is filled with oil of density 710 kg/m3. What mass must be placed on the small piston to support a car of mass 1400 kg at equal fluid levels? m = With the lift in balance with equal fluid levels, a person of mass 90 kg gets into the car. What is the equilibrium height difference in the fluid levels in the pistons? Δh...
What force (in N) must be exerted on the master cylinder of a hydraulic lift to...
What force (in N) must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2200 kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.50 cm diameter, while the slave has a 24.0 cm diameter.
A hydraulic jack has an input piston of area 0.0520 m2 and an output piston of...
A hydraulic jack has an input piston of area 0.0520 m2 and an output piston of area 0.740 m2. How much force (in N) on the input piston is required to lift a car weighing 1.70 ✕ 104 N? ? = N
A hydraulic jack used to lift cars is called a three-ton jack. The large piston is...
A hydraulic jack used to lift cars is called a three-ton jack. The large piston is 22 mm in diameter, the small one 6.3 mm. Assume that a force of 3 tons is 3.0 x 104 N. a. What force must be exerted on the small piston to lift the 3-ton weight? b. Most jacks use a lever to reduce the force needed on the small piston. If the resistance arm is 3.0 cm, how long is the effort arm...
A 1225-kg car is raised using a hydraulic lift, which consists of a U-tube with arms...
A 1225-kg car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with oil with a density of 800. kg/m3 and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 18.0 cm and the narrower arm has a radius of 5.00 cm. The car rests on the piston on the wider arm of the U-tube. The wider piston is raised to a position that...