Question

What is the difference in behavior of a solid aluminum ring and an aluminum ring with...

What is the difference in behavior of a solid aluminum ring and an aluminum ring with a gap cut in it when placed on the core of a solenoid that has the current turned on? Why do you think this is?

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

when we turn on the solenoid magnetic flux linked with both the rings changes and due to lenz's law both the ring will try to oppose it because of which, an emf will be induced in both the rings. but because of this indiced emf current is induced in solid ring only. because for current to flow circuit must be coplete and i ring with gap circiuit is not copmlete. so solid ring will be ejected due to opposite current induced in it but ring with a gap would not be ejected.

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
An aluminum ring with a radius of 5.00 cm and a resistance of 2.85 10-4 is...
An aluminum ring with a radius of 5.00 cm and a resistance of 2.85 10-4 is placed on top of a long air-core solenoid with 1030 turns per meter and radius of 3.00 cm, as shown in Figure P31.7. Assume the axial component of the field produced by the solenoid over the area of the end of the solenoid is one-half as strong as at the center of the solenoid. Assume that the solenoid produces negligible field outside its cross-sectional...
An iron rod goes vertically through a solenoid. An aluminum ring is slipped over the rod...
An iron rod goes vertically through a solenoid. An aluminum ring is slipped over the rod down to the solenoid. When the current runs through the solenoid, the ring jumps up. If the current reverses while the ring is rising, the ring will be pulled back there will be no effect. the ring will be pushed up more
At 20∘C, the hole in an aluminum ring is 2.100 cm in diameter. You need to...
At 20∘C, the hole in an aluminum ring is 2.100 cm in diameter. You need to slip this ring over a steel shaft that has a room-temperature diameter of 2.107 cm To what common temperature should the ring and the shaft be heated so that the ring will just fit onto the shaft? Coefficients of linear thermal expansion of steel and aluminum are 12×10−6 K−1 and 23×10−6 K−1 respectively.
At 20∘C, the hole in an aluminum ring is 2.400 cm in diameter. You need to...
At 20∘C, the hole in an aluminum ring is 2.400 cm in diameter. You need to slip this ring over a steel shaft that has a room-temperature diameter of 2.404 cm .To what common temperature should the ring and the shaft be heated so that the ring will just be fitted on the shaft? Coefficients of linear thermal expansion of steel and aluminum are 12*10-6 K-1 and 23*10-6 K-1 respectively.
At 20∘C, the hole in an aluminum ring is 2.200 cm in diameter. You need to...
At 20∘C, the hole in an aluminum ring is 2.200 cm in diameter. You need to slip this ring over a steel shaft that has a room-temperature diameter of 2.204 cm . To what common temperature should the ring and the shaft be heated so that the ring will just fit onto the shaft? Coefficients of linear thermal expansion of steel and aluminum are 12×10-6K-1 and 23×10-6K-1 respectively. Express your answer in degrees Celsius to two significant figures.
At 20.0°C, an aluminum ring has an inner diameter of 5.00 cm and a brass rod...
At 20.0°C, an aluminum ring has an inner diameter of 5.00 cm and a brass rod has a diameter of 5.055 cm. (a)If only the ring is warmed, what temperature must it reach so that it will just slip over the rod? (b) If both the ring and the rod are warmed together, what temperature must they both reach so that the ring barely slips over the rod? (c) Why might the temperature value of part (b)pose problems for this...
A toroidal core of relative permeability ?? = 3000, has a mean radius R = 80...
A toroidal core of relative permeability ?? = 3000, has a mean radius R = 80 mm and a circular cross section with radius b = 25 mm. An airgap ?? = 3 mm exists, and a current I flows in a 500-turn winding to produce a magnetic flux of 10−5 Wb, as shown in Figure Q2(a). Neglecting flux leakage and using mean path length, find: 1. The reluctances of the air gap and the iron core 2. ?? and...
Ethics: Accepted social and organizational behavior. Based on the above definition, what do you think could...
Ethics: Accepted social and organizational behavior. Based on the above definition, what do you think could be some critical ethical issues regarding management information systems? When could these ethical issues become legal? why?
A 5-m-long cylinder of solid aluminum has a radius of 2 cm. (a) If the cylinder...
A 5-m-long cylinder of solid aluminum has a radius of 2 cm. (a) If the cylinder is at a temperature of 5 °C, how much will the length change when the temperature rises to 30 °C? (b) Due to the temperature increase, by how much would the density of the aluminum cylinder change? The density decreases by % upon heating. c) By what percentage does the volume of the cylinder increase? The volume increases by % upon heating.
What do you think is your consumer buying behavior? What factors do you think shape your...
What do you think is your consumer buying behavior? What factors do you think shape your buying behavior?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT