Question

question1. Find the total capacitance of the capacitors pictured in the figure below. Let C1 =...

question1.
Find the total capacitance of the capacitors pictured in the figure below. Let C1 = 7.7 µF and C2 = 45.9 µF. Express your answer in µF.

question 2.
In the question above, let C1 = C2 = 5.0 µF . If the network of capacitors was connected to a 100 Volt battery, how much charge would be on C2? Express your answer in microcoulombs.
Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
For the system of capacitors shown in the figure below, find the following. (Let C1 =...
For the system of capacitors shown in the figure below, find the following. (Let C1 = 9.00 µF and C2 = 1.00 µF.) A circuit consists of a 90.0 V battery and four capacitors. The wire begins at the positive terminal of the battery and splits into two parallel branches before reconnecting and then ending at the negative terminal of the battery. Each branch contains two capacitors in series. One branch contains a capacitor labeled C1 followed by a 6.00...
Find the total capacitance of the combination of capacitors shown in the figure below. (C1 =...
Find the total capacitance of the combination of capacitors shown in the figure below. (C1 = 2.92
Now let’s look at a specific problem involving series and parallel combinations of capacitors. Two capacitors,...
Now let’s look at a specific problem involving series and parallel combinations of capacitors. Two capacitors, one with C1=6.0μF and the other with C2=3.0μF, are connected to a potential difference of Vab=18V. Find the equivalent capacitance, and find the charge and potential difference for each capacitor when the two capacitors are connected (a) in series and (b) in parallel. PART A: Repeat this example for  Vab=18V and C1=C2=10μF. What is the equivalent capacitance for the capacitors when they are connected in...
1. Three capacitors are connected in series and give an effective capacitance of 22 nF. If...
1. Three capacitors are connected in series and give an effective capacitance of 22 nF. If C1 = 5 µF and C3 = 100 nF, what is C2? Suppose V1 = 5 V. Find the charge on and voltage across the other two capacitors. Again, calculate energy stored. 2. A parallel plate capacitor has plates with area 10 cm2 and a gap of 2 mm. First, find the capacitance of this capacitor. Now, imagine a metal plate of thickness 0.25...
Consider the following. (Let C1 = 14.40 µF and C2 = 8.40 µF.) A rectangular circuit...
Consider the following. (Let C1 = 14.40 µF and C2 = 8.40 µF.) A rectangular circuit contains a battery and four capacitors. The bottom side has a 9.00 V battery with the positive terminal on the left. The left and right sides of the circuit each contain a capacitor labeled C1. The top side splits into two parallel horizontal branches, which recombine before reaching the top right corner. There is a 6.00 µF capacitor on the upper branch and a...
Four capacitors are connected as shown in the figure below. (Let C = 20.0 µF.) A...
Four capacitors are connected as shown in the figure below. (Let C = 20.0 µF.) A circuit consists of four capacitors. It begins at point a before the wire splits in two directions. On the upper split, there is a capacitor C followed by a 3.00 µF capacitor. On the lower split, there is a 6.00 µF capacitor. The two splits reconnect and are followed by a 20.0 µF capacitor, which is then followed by point b. (a) Find the...
Learning Goal: To understand how to calculate capacitance, voltage, and charge for a combination of capacitors...
Learning Goal: To understand how to calculate capacitance, voltage, and charge for a combination of capacitors connected in series. Consider the combination of capacitors shown in the figure.(Figure 1) Three capacitors are connected to each other in series, and then to the battery. The values of the capacitances are C, 2C, and 3C, and the applied voltage is ?V. Initially, all of the capacitors are completely discharged; after the battery is connected, the charge on plate 1 is Q Part...
Consider the circuit shown below where four capacitors, C1=1.3  μF ,  C2=3.7  μF , C3=2.5  μF and C4=1.2  μF are connected...
Consider the circuit shown below where four capacitors, C1=1.3  μF ,  C2=3.7  μF , C3=2.5  μF and C4=1.2  μF are connected to a battery of voltage V=41 V. Determine the voltage on C2. Express your answer using one decimal place in units of Volts.
A capacitor C1 =1F is connected to a 1V battery using a wire with a total...
A capacitor C1 =1F is connected to a 1V battery using a wire with a total resistance R = 1Ohm. Suppose after the charging is complete the capacitor C1 is connected to another capacitor C2 = 2 F using a wire with a total resistance of R =0.3 Ohm. Now the first capacitor discharges while the second one charges. Let’s derive the differential equation describing the discharge in this 2-capacitor circuit. Let’s label the charge on the capacitor C1 as...
An ultracapacitor is a very high-capacitance device capable of storing much more energy than an ordinary...
An ultracapacitor is a very high-capacitance device capable of storing much more energy than an ordinary capacitor. It is designed so that the spacing of the plates is around 1000 times smaller than in ordinary capacitors. Furthermore the plates contain millions of microscopic nanotubes, which increase their effective area 100,000 times. 1) If the plate separation and effective area of a 10-μμF capacitor are changed as described above to make an ultracapacitor, what is its new capacitance? (ONE significant figure)...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT