Question

2 parts! thanks :) 1. A water pipe with an inner diameter of 2.5 cm carries...

2 parts! thanks :)

1. A water pipe with an inner diameter of 2.5 cm carries water into the basement of a house at a speed of 0.88 m/s and a pressure of 180 kPa. If the pipe tapers to an inner diameter of 1.2 cm and rises to the second floor 7.2 m above the input level, what is the speed of the water flow at the second floor?

Your answer should be in m/s, but enter only the numerical part in the box.

2. A water pipe with an inner diameter of 2.7 cm carries water into the basement of a house at a speed of 0.98 m/s and a pressure of 168 kPa. If the pipe tapers to an inner diameter of 1.1 cm and rises to the second floor 7.3 m above the input level, what is the water pressure at the second floor?

Your answer should be in kPa, but enter only the numerical part in the box.

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Water circulates through a hot-water heating system in a house. The water leaves the basement with...
Water circulates through a hot-water heating system in a house. The water leaves the basement with a speed of 0.5 m/s through a 4-cm-diameter pipe, under a total pressure of 3Patm. (Assume that all the pipes have circular cross-sectional areas and that the pipes don't "branch off" at any point.) a) If the pipe on the second floor of the house has a smaller radius than the basement pipe, will the speed of the water in the second-floor pipe be...
6. Water is used to circulate heat through a house. The water starts in the basement...
6. Water is used to circulate heat through a house. The water starts in the basement with a speed of 0.8 m/s in a pipe and a pressure of 3.46 atm. The pipe goes up 6 m to the top floor with a new pressure of 2.78 atm and new diameter of 2.5 cm in diameter. Find the new water speed in the second part of the pipe and the initial diameter of the pipe
A pipe carries water from point 1 where the diameter is 8 cm and the elevation...
A pipe carries water from point 1 where the diameter is 8 cm and the elevation above the datum is 4 m, to point 2 where the diameter is 4 cm and the elevation above the datum is 10 m. The volumetirc flow rate is 0.0375 m^3/s, and the pressure at point 1 is 988 kPa. Assuming no frictional losses, determine the pressure at point 2.
The water enters the two-story building through a horizontal pipe with an inner diameter 4 cm...
The water enters the two-story building through a horizontal pipe with an inner diameter 4 cm and the pressure of 10 atm. The velocity of the water flow in the pipe is 5 m/s. The horizontal pipe is connected to a vertical pipe which leads to bathrooms in each story. a) What is the velocity of the water flow in the vertical pipe if the diameter of the pipe is 2 cm. b) What is the pressure in the pipe...
Water enters a basement Inlet pipe of radius 1.7 cm at 52 cm / s. It...
Water enters a basement Inlet pipe of radius 1.7 cm at 52 cm / s. It flows through a pipe of radius 0.49 cm at a height of 36 m at a gauge pressure 0.3 atm. What is the gauge pressure at the basement? Give your answer to two decimal places and remember add unit kPa after the numerical value.
In a section of horizontal pipe with a diameter of 4.0 cm, the pressure is 115...
In a section of horizontal pipe with a diameter of 4.0 cm, the pressure is 115 kPa and water is flowing with a speed of 1.5 m/s. The pipe narrows to a 3.0-cm diameter. What is the pressure in kPa in the narrower region? Treat the water as an ideal incompressible fluid.
In a section of horizontal pipe with a diameter of 5.00 cm the pressure is 6.52...
In a section of horizontal pipe with a diameter of 5.00 cm the pressure is 6.52 kPa and water is flowing at a speed of 1.70 m/s. Then it narrows to 2.70 cm. What is the pressure in the narrow region if water behaves as an ideal fluid?
A 2.0 cm -diameter venturi flowmeter is inserted in a 3.0 cm -diameter pipe carrying water...
A 2.0 cm -diameter venturi flowmeter is inserted in a 3.0 cm -diameter pipe carrying water (density =1000 kg/m3). The pressure difference between venturi and unconstricted pipe is 15 kPa. What is the flow speed in the pipe? What is the volume flow rate?
1- Water flows in a 10 m long and 4 cm diameter pipe contains 4 elbows...
1- Water flows in a 10 m long and 4 cm diameter pipe contains 4 elbows ( KL= 0.2 ) at velocity 8 m/s. Calculate the total head losses when the friction factor f=0.03 35.56 m 22.07 m 27.07 m 15.46 m 2- water flows in a 10 m long and 5 cm diameter horizontal pipe at rate 15 l/s Calculate the pressure drop Take the density of water 1000 kg/m3 and the dynamic viscosity 0.001 kg/m.s 74.13 kPa 96.41...
A pipe of radius 10 cm has a pressure of 1.2 x 105 N/m2 as it...
A pipe of radius 10 cm has a pressure of 1.2 x 105 N/m2 as it goes up to a second floor 3.1 m up, it decreases in size to a radius of 5 cm and a water speed of 8.0 m/s Find the water speed in the first part of the pipe. Find the pressure in the second part of the pipe.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT