Question

How long will it take a 7.08 hp motor to lift a 250 kg beam at...

How long will it take a 7.08 hp motor to lift a 250 kg beam at a constant velocity from the ground to a height of 45.0m? Assume frictional forces are negligible. (Please Work this out and show equations)

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1


0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A 60 hp motor provides the power for an elevator in a hotel. If the weight...
A 60 hp motor provides the power for an elevator in a hotel. If the weight of an elevator and its occupants is 2000 lb, how much time in seconds will it take to lift the elevator from the ground level to the 10th floor, a distance of 120 ft? A.) 6.97 B.) 7.27 C.) 8.59 D.) 9.34
1. A cable attached to a helicopter is used to vertically lift a 2650-kilogram elephant at...
1. A cable attached to a helicopter is used to vertically lift a 2650-kilogram elephant at a constant velocity of 0.8 m/s. Draw a free-body diagram for the elephant. Label all forces acting on the elephant. Determine the size of each force that is acting on the elephant. 2. A landscaper pushes a 64 kg wheelbarrow due east at a constant velocity of 1.15 m/s. The opposing frictional force is -12.5 kgm/s^2. What are the forces acting on the wheelbarrow...
The builders of the pyramids used a long ramp to lift 21000-kg (21.0-ton) blocks. If a...
The builders of the pyramids used a long ramp to lift 21000-kg (21.0-ton) blocks. If a block rose 0.930 m in height while traveling 18.0 m along the ramp’s surface, how much uphill force was needed to push it up the ramp at constant velocity? Use g=9.81 m/s2.
A uniform beam, 2.00 m long with a mass of 20.0 kg, is mounted to a...
A uniform beam, 2.00 m long with a mass of 20.0 kg, is mounted to a wall with a hinge. The beam is held out horizontally by a steel cable, 5 mm in diameter, that makes a 30-degree angle with the beam. The beam will hold up a sign that will hang off its end. See the diagram below A.Using a safety factor of 5, what is the maximum tension the steel cable can provide? B.Given the free-body diagram as...
Lets go ahead and assume that there is a 40 kg object is pushed upwards that...
Lets go ahead and assume that there is a 40 kg object is pushed upwards that will be at a constant velocity for 8 m along a 30° inclined plane by the horizontal force F. The coefficient of kinetic friction between the box and the surface will be 0.4. Please show the work for the following four forces below: Note: Please give small explanation on the parts with work and solution. a. Applied force b. Frictional force c. Gravitational force...
Early one October, you go to a pumpkin patch to select your Halloween pumpkin. You lift...
Early one October, you go to a pumpkin patch to select your Halloween pumpkin. You lift the 2.8 kg pumpkin to a height of 1.0 m , then carry it 50.0 m (on level ground) to the check-out stand. A)Calculate the work you do on the pumpkin as you lift it from the ground.B) How much work do you do on the pumpkin as you carry it from the field?
a. How long (in s) would it take a 1.50 ? 105 kg airplane with engines...
a. How long (in s) would it take a 1.50 ? 105 kg airplane with engines that produce of 100 MW of power to reach a speed of 250 m/s and an altitude of 12.0 km if air resistance were negligible? b.If it actually takes 925 s, what is the power applied, in megawatts? c. Given this power, what is the average force (in kN) of air resistance if the airplane takes 1200 s? (Hint: You must find the distance...
Question 26.) Lets go ahead and assume that there is a 40 kg object is pushed...
Question 26.) Lets go ahead and assume that there is a 40 kg object is pushed upwards that will be at a constant velocity for 8 m along a 30° inclined plane by the horizontal force F. The coefficient of kinetic friction between the box and the surface will be 0.4. Please show the work for the following four forces below: a. Applied force b. Frictional force c. Gravitational force d. Net force
Sam dropped a ball from a height of 200 cm. Find out (a) how long it...
Sam dropped a ball from a height of 200 cm. Find out (a) how long it will take to hit the ground and (b) what would be its velocity when it hits the ground? (c) If mass of the ball is 500 g, what would be its kinetic energy when it hits the ground? (d) What would be its potential energy before its fall? Please explain procedure
How long will it take to plate out 4.9 kg of Ni from aqueous Ni4+ with...
How long will it take to plate out 4.9 kg of Ni from aqueous Ni4+ with a current of 135.0 A?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT