Question

1)Explain step response of a RL series circuit and support your answer with waveform.

1)Explain step response of a RL series circuit and support your answer with waveform.

Homework Answers

Answer #1

apply krichoffs voltage law in the RL closed loop

i hope you under stand

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
With neat waveforms explain step response of a RC series circuit.
With neat waveforms explain step response of a RC series circuit.
A RL series circuit has a 1Kohm resistor and an 1 mH inductor, determine its time...
A RL series circuit has a 1Kohm resistor and an 1 mH inductor, determine its time constant.
A series RL circuit consists of a 6.3 volt battery, a 175 ohm resistor and an...
A series RL circuit consists of a 6.3 volt battery, a 175 ohm resistor and an inductor. (a) If the battery has been connected for a long time interval, what is the current in the circuit? (b) The battery is then removed from the circuit, so only the resistor and the inductor are connected in series. What is the inductance of the inductor if the current drops to half of its peak value in 2.00 ms? (c) The current is...
R = 100 ohms in a series RLC circuit. C capacitor disable (RL) current, pi /...
R = 100 ohms in a series RLC circuit. C capacitor disable (RL) current, pi / 3 radian lags behind the voltage. When the inductor L is removed (RC), the current rises more than the voltage up to pi / 3 radians. Find the total impedance of the circuit
(15-17)         An AC series RL circuit has a source RMS voltage of 100 V, an inductance...
(15-17)         An AC series RL circuit has a source RMS voltage of 100 V, an inductance of 50 mH, and a resistance of 10 W. The AC source operates at 60 Hz. 15.         For this circuit, which of the following is true? Group of answer choices The current leads the source voltage. The current lags the source voltage. The current and source voltage are in phase. None of the above. Which of the following for this circuit has the greater...
Consider the RL circuit shown in the figure (Figure 1). When the switch is closed, the...
Consider the RL circuit shown in the figure (Figure 1). When the switch is closed, the current in the circuit is observed to increase from 0 to 0.33 A in 0.14 s . What is the inductance L? Express your answer using two significant figures How long after the switch is closed does the current have the value 0.51 A ? Express your answer using two significant figures.
7) (a) Draw a circuit of a high pass RL filter b) Derive the expression for...
7) (a) Draw a circuit of a high pass RL filter b) Derive the expression for V_o/V_i of a high pass RL filter (c) Use the equation you derived in (b) to determine the gain when (i) the frequency is very low (ii) R = X_L (iii) the frequency is very high (d) Use the equation you derived in (b) to determine the phase angle when (i) the frequency is very low (ii) R = X_L (iii) the frequency is...
C7.1 Consider a single-loop RL circuit just like the one in activity 1. When the applied...
C7.1 Consider a single-loop RL circuit just like the one in activity 1. When the applied voltage is equal to 4.5V, the current also has a nonzero value. When the applied voltage drops to zero, the current in the circuit does not go to zero instantaneoulsy. Explain why the current does not go to zero instantaneously. Please let me have reason, theroy and answer.
An RL circuit with L = 23 mH has an emf of 12 V applied to...
An RL circuit with L = 23 mH has an emf of 12 V applied to it starting at time t = 0. When t = 0.19 ms, the rate of change of current in the circuit is 263 A/s. Determine the resistance. Express your answer in ohms.
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your...
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your choice with AC source. Find the resonance conditions (resonant frequency, quality factor cut-off frequencies and bandwidth. Simulate(multisim) the resonance condition by experimenting with AC signal of several different frequencies and comparing the output amplitudes. You need to show graphs of simulation with several different frequencies. Demonstrate that the simulation results confirm the calculated resonance effect. Make a band pass filter from circuit in (1)....
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT