Question

A rod, 120.0 cm long and of diameter 3.00 cm is subjected to an axial pull...

A rod, 120.0 cm long and of diameter 3.00 cm is subjected to an axial pull of 18.0 kN. Axial means in the direction of the length of the rod. Find the stress in N/mm2 .

(Continued from the previous question)

A steel rod, 120.0 cm long and of diameter 3.00 cm is subjected to an axial pull of 18.0 kN. Axial means in the direction of the length of the rod. What is the percentage of the resulting strain?

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Note: here type of steel is not mentioned so i took the tensile strength of stainless steel, if it is something else then please let me know, I will correct it.

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Q3: Tension test was conducted on a mild steel rod having diameter 1.5 cm and length...
Q3: Tension test was conducted on a mild steel rod having diameter 1.5 cm and length 20 cm. While applying a load of 10 kN, there will be an extension of 0.012 cm on a length of 20 cm. Maximum load carried by the rod was found to be 26 kN and the load beyond which stress is not proportional to strain was observed to be 11 kN. When the specimen breaks, the extension of the rod for 20 cm...
A single crystal Al2O3 rod (precisely 6 mm diameter × 60 mm long) is used to...
A single crystal Al2O3 rod (precisely 6 mm diameter × 60 mm long) is used to apply loads to small samples in a high-precision dilatometer (a length-measuring device). Calculate the resulting rod dimensions if the crystal is subjected to a 27 kN axial compression load. Express your answer to five significant figures.
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
In a bar drawing manufacturing process a2.0” long rod with a diameter of 0.5” is pulled...
In a bar drawing manufacturing process a2.0” long rod with a diameter of 0.5” is pulled with a F=6000 lb. force.The diameter decreases permanently to 0.4”. Determine: a.The final length of the rod b.The true stress and strain at this load. c. The engineering stress and strain at this load. d. The stress at which necking occurs. e. If the length just before necking occurs is 4.0 “ , find the force at which necking occurs. Strength coefficient k= 100...
Strength of Material A steel rod is 2m long with a diameter of 30mm has a...
Strength of Material A steel rod is 2m long with a diameter of 30mm has a standard temperature of 18℃. It is exposed in a room with a temperature of 40 ℃. Use ? = 11.6 ? 10−6/℃ and E = 200 GPa. Find a.) the thermal deformation, b.) thermal stress and c.) instead of heating the rod, what equivalent axial deformation is necessary to have a deformation that is the same as the deformation due to the change in...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 150 N and thermal loading which imposes a longitudinal force of 230 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.5 mm in length at both ends and decreasing by 0.0125 mm at...
Consider a rod that is 0.220 cm in diameter and 1.50 m long, with a mass...
Consider a rod that is 0.220 cm in diameter and 1.50 m long, with a mass of 0.0400 kg. 1. Find the moment of inertia about an axis perpendicular to the rod and passing through one end.(kg*m^2 units please) 2. Find the moment of inertia about an axis along the length of the rod. Express your answer in kilogram meters squared.
4. [15 pts] A 4.00 m long, 7.50 cm diameter rod is made of an unknown...
4. [15 pts] A 4.00 m long, 7.50 cm diameter rod is made of an unknown metal. In order to determine the type of metal, a 2500 N force is exerted on each end of the rod, causing the length of the rod to decrease by 2.50*10-5 m. What metal is the rod made of?
A long, straight metal rod has a radius of 4.20 cm and a charge per unit...
A long, straight metal rod has a radius of 4.20 cm and a charge per unit length of 34.4 nC/m. Find the electric field at the following distances from the axis of the rod, where distances are measured perpendicular to the rod's axis. (a) 2.00 cm magnitude   N/C direction ---Select--- inward outward magnitude is zero (b) 14.0 cm magnitude   N/C direction ---Select--- inward outward magnitude is zero (c) 140 cm magnitude   N/C direction ---Select--- inward outward magnitude is zero
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT