Question

The turns ratio of a transformer used in a Bridge Rectifier is 2:1. The primary is...

The turns ratio of a transformer used in a Bridge Rectifier is 2:1. The primary is connected to the power mains: 210V, 50Hz. Assuming the diode voltage drops to be zero, (a) calculate the DC voltage across the load resistor. (b) What is the PIV of the diode? If the same dc voltage is obtained by using Center tapped FWR, what is PIV?
WITH ALL STEPS

Homework Answers

Answer #1

Output to secondary terminal

DC dutput to load resistance.

Output Dc is of 55V.

PIV in HWR is given as

Part:b

Let Vm is maximum voltage to center tapped FWR.

so only 77.78 voltage need at secondary terminal.

Now PIV in FDR for center tapped

I hope it helps you.

Thanks for asking.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
. The turns ratio of a transformer used in a Bridge Rectifier is 12:1. The primary...
. The turns ratio of a transformer used in a Bridge Rectifier is 12:1. The primary is connected to the power mains: 220V, 50Hz. Assuming the diode voltage drops to be zero, (a) calculate the D.C voltage across the load resistor. (b) What is the PIV of the diode? If the same dc voltage is obtained by using Center tapped FWR, what is PIV?
A transformer has a primary-to-secondary turns ratio of 100:1. The voltage on the primary side is...
A transformer has a primary-to-secondary turns ratio of 100:1. The voltage on the primary side is 27.7 kv.a.c. at 60.0 Hz ( assume 60.0 Hz when treating electric power topics). A load is connected across the secondary winding. Assume that the transformer is ideal. (a) Suppose that the electric utility supplied 27.7 kv.d.c. rather than 27.7 kv.a.c. How much power would the transformer’s secondary winding deliver to the load in this case? (b). The transformer’s primary winding is supplied by...
2(a). A transformer has a primary-to-secondary turns ratio of 100:1. The voltage on the primary side...
2(a). A transformer has a primary-to-secondary turns ratio of 100:1. The voltage on the primary side is 27.7 kv.a.c. at 60.0 Hz ( assume 60.0 Hz when treating electric power topics). A load is connected across the secondary winding. Assuming that the transformer is ideal, what voltage is developed to the load? Briefly show your work. Sketch a diagram. 2(b). The load of part a is a 2.00-ohm load. How much current does the load draw from the transformer’s secondary...
Full wave rectifier is used to design a DC power supply. The DC power supply has...
Full wave rectifier is used to design a DC power supply. The DC power supply has an average output voltage of 12v on which the maximum ripple allowed is 1v (peak to peak). The rectifier feeds a load of 200ohm . The rectifier is supplied from 170v at 60 hz ac line through a transformer. Assume Vy= 0.7v . a) Find the transformer tarns ratio? b) Find the required value of the capacitor? c) Specify the PIV rating of the...
An ideal step-down transformer has a primary coil of 370 turns and a secondary coil of...
An ideal step-down transformer has a primary coil of 370 turns and a secondary coil of 25 turns. Its primary coil is plugged into an outlet with 115 V(AC), from which it draws an rms current of 0.69 A. What is the voltage in the secondary coil? Calculate the rms current in the secondary coil. Assuming that the transformer secondary is driving a resistive load, calculate the average power dissipated in the resistor.
A transformer has 500. primary turns and 10.0 secondary turns. (a) If Vp is 120.V(rms), what...
A transformer has 500. primary turns and 10.0 secondary turns. (a) If Vp is 120.V(rms), what is Vs? If the secondary now has a resistive load of 10.0Ω, what is the current in the (b) secondary and (c) primary? (Hints: Input power equals the output power. Express power in terms of voltage and current, then use Faraday’s Law to relate voltage to number of turns and change of flux. If the primary and the secondary are connected via a closed...
a) An ideal step-down transformer has a primary coil of 400 turns and a secondary coil...
a) An ideal step-down transformer has a primary coil of 400 turns and a secondary coil of 14 turns. Its primary coil is plugged into an outlet with 240 V(AC), from which it draws an rms current of 0.35 A. What is the voltage in the secondary coil? b) Calculate the rms current in the secondary coil. c) Assuming that the transformer secondary is driving a resistive load, calculate the average power dissipated in the resistor.
A transformer connected to a 120 −V ac line is to supply 12.0 VV (rms) to...
A transformer connected to a 120 −V ac line is to supply 12.0 VV (rms) to a portable electronic device. The load resistance in the secondary is 5.20 ΩΩ . - What should the ratio of primary to secondary turns of the transformer be, What rms current must the secondary supply? - What average power is delivered to the load, What resistance connected directly across the source line (which has a voltage of 120 −V) would draw the same power...
An ideal transformer has 100 turns on its primary coil and 200 turns on its secondary...
An ideal transformer has 100 turns on its primary coil and 200 turns on its secondary coil. If 120 V at 2.0 A is applied to the primary, (a) What voltage is present in the secondary? (b) What current is present in the secondary? (c) What is the output power? (d) Is this a step-up or step-down transformer? (e) Is the input power the same, larger or smaller than the output power?
(c) A voltage transformer for use on an 11 kV system has a star connected primary....
(c) A voltage transformer for use on an 11 kV system has a star connected primary. If the turns ratio is 100/1 what will be the residual voltage of the open delta winding? (d) A 1 A electromagnetic relay has 80 turns on minimum setting. If the settings are from 50% to 200% in 25% steps, calculate the plug bridge turns for each setting. If the relay presents a burden of 3 VA determine the number of turns required if...