Question

Consider a low pass filter using R=1kohm and C 10nF. (a) Find the frequeny where gain...

Consider a low pass filter using R=1kohm and C 10nF. (a) Find the frequeny where gain is 50%(f3db)? (b) Plot the Bode plot (log Gain vs.log f). (c) Plot the phase shift versus log f.

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. Consider a low pass filter using R=1 k Ω and C=10 nF . (a) Find...
1. Consider a low pass filter using R=1 k Ω and C=10 nF . (a) Find the frequency where the gain is 50% ( f 3dB) ? (b) Plot the Bode plot ( log Gain vs. log f ). (c) Plot the phase shift versus log f.
1. Can the phase angle for a single-stage low pass electronic filter be greater than 90...
1. Can the phase angle for a single-stage low pass electronic filter be greater than 90 degrees? Explain using ac circuit theory. 2. How to determine the cutoff frequency for a single-stage low pass electronic filter using a bode plot and phase plot?
Please show steps. Thank you Design an identical cascade unit gain active RC low pass filter...
Please show steps. Thank you Design an identical cascade unit gain active RC low pass filter of order 4. The cut frequency for the filter is 800Hz. Use 1.0uF capacitors. a) Draw the circuit and calculate the values of R. b) Express the transfer function of the filter H(s). c) Plot the Bode diagram of the frequency response of the filter. d) Estimate the output voltage if the filter is excited with an input voltage vi(t) = sin(15000t) e) What...
Design and draw a simple electrical circuit (a combination of a low-pass and a high-pass filter...
Design and draw a simple electrical circuit (a combination of a low-pass and a high-pass filter circuits) that will act as a bandpass filter for frequencies between 0.1 and 100 rad/s. Generate the magnitude Bode plot on matlab!!! Please do the matlab! thank you!
7) (a) Draw a circuit of a high pass RL filter b) Derive the expression for...
7) (a) Draw a circuit of a high pass RL filter b) Derive the expression for V_o/V_i of a high pass RL filter (c) Use the equation you derived in (b) to determine the gain when (i) the frequency is very low (ii) R = X_L (iii) the frequency is very high (d) Use the equation you derived in (b) to determine the phase angle when (i) the frequency is very low (ii) R = X_L (iii) the frequency is...
Design a two pole low pass Butterworth active filter using a unity gain section to achieve...
Design a two pole low pass Butterworth active filter using a unity gain section to achieve a 3dB frequency of 1kHz. Select the two filter resistances as 10k (ohms) each.
MATLAB. Design your own low-pass shelving filter which can boost the low frequency of given music...
MATLAB. Design your own low-pass shelving filter which can boost the low frequency of given music signal. After designing filter, apply the filter to the original music signal and observe the result. Include following plots. A. Magnitude and phase plot of your filter. B. Magnitude plot of original signal C. Magnitude plot of filtered signal
Draw a 2nd order low pass filter with a flat passband gain of 5 to remove...
Draw a 2nd order low pass filter with a flat passband gain of 5 to remove the harmonic content of a 60 HZ square wave of triangular wave input. Design for a cut off frequency of 80 Hz. Use 50 K Ohm for the input resistance. Verify your answers using AC Sweep in PSPICE
An active low pass filter (with op-amp), the capacitor value is 500 pf, the resistor value...
An active low pass filter (with op-amp), the capacitor value is 500 pf, the resistor value is 1kΩ and the input signal source is 20 V. a)draw the complete circuit with the data provided in the example b) plot the frequency response graph of the filter, use at least 5 dots for the plot of the graph and identify in it the pass band and the attenuation band. c) determine the filter output voltage f = 100KHz and f =...
1. Design a second-orderactive low-pass filter to amplify the frequencies below 1 kHzwith gain of Av=150.Sketch...
1. Design a second-orderactive low-pass filter to amplify the frequencies below 1 kHzwith gain of Av=150.Sketch the circuit and determine the component values. 2.Design a second-order active high-pass filter to amplify the frequencies above 500 Hzwith gain of Av=100.Sketch the circuit and determine the component values. 3.Design a second-order active band-pass filter to amplify the frequencies between 500?1000 Hz with gain of Av=200.Sketch the circuit and determine the component values
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT