Question

A rotating cylindrical rod of mass m=4 Kg and length l=1 meter is connected to a...

A rotating cylindrical rod of mass m=4 Kg and length l=1 meter is connected to a falling weight of 300 grams with a 2 meters string (Maximum distance covered by the falling weight). The distance from the wound string to the axis of rotation is 300 mm. The time taken by the falling weight to halfway is 2 seconds and to the bottom is 3.7 seconds.

!!!! If we replace the 300-gram falling weight with the 2 Kg weight, it takes 0.4 seconds to reach to the halfway mark and 0.9 seconds to the bottom.

  1. Calculate the corresponding angular momentum at halfway and bottom.
  2. Briefly explain the relation between falling weight and angular momentum.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A rotating cylindrical rod of mass m=4 Kg and length l=1 meter is connected to a...
A rotating cylindrical rod of mass m=4 Kg and length l=1 meter is connected to a falling weight of 300 grams with a 2 meters string (Maximum distance covered by the falling weight). The distance from the wound string to the axis of rotation is 300 mm. The time taken by the falling weight to halfway is 2 seconds and to the bottom is 2.7 seconds. If we replace the 300-gram falling weight with the 2 Kg weight, it takes...
A rotating cylindrical rod of mass m=4 Kg and length l=1 meter is connected to a...
A rotating cylindrical rod of mass m=4 Kg and length l=1 meter is connected to a falling weight of 300 grams with a 2 meters string (Maximum distance covered by the falling weight). The distance from the wound string to the axis of rotation is 300 mm. The time taken by the falling weight to halfway is 2 seconds and to the bottom is 2.7 seconds. Change of angular momentum in the spinning rod Mass (Kg) Moment of Inertial of...
A cylindrical rod of mass 0.82 kg and length 1.88 m is free to rotate about...
A cylindrical rod of mass 0.82 kg and length 1.88 m is free to rotate about a pivot fixed at one end. A ball (mass 3.2 kg) is attached to the other end of the rod. The rod-and- ball system is held in a horizontal position by a vertical force that acts 1.41 m from the pivot. The force is then removed, and the rod-and-ball swings down. (a) (4 points) What was the vertical force used to hold the system...
A cylindrical rod of length 2.0 m, radius 0.5 m, and mass 1.5 kg has two...
A cylindrical rod of length 2.0 m, radius 0.5 m, and mass 1.5 kg has two spheres attached on its ends. The centers of the spheres are 1.0 m from the center of the rod. The mass of each sphere is 0.66 kg. The rod is capable of rotating about an axis passing through its center and perpendicular to the plane of the page, but the set up is stationary to begin with. A small mass of value 0.19 kgmoving...
8%) Problem 15:   A rod of mass M = 3.5 kg and length L can rotate...
8%) Problem 15:   A rod of mass M = 3.5 kg and length L can rotate about a hinge at its left end and is initially at rest. A putty ball of mass m = 55 g, moving with speed v = 6.68 m/s, strikes the rod at angle θ = 59° from the normal at a distance D = 2/3 L, where L = 1.25 m, from the point of rotation and sticks to the rod after the collision....
A thin, cylindrical rod ℓ = 27.0 cm long with a mass m = 1.20 kg...
A thin, cylindrical rod ℓ = 27.0 cm long with a mass m = 1.20 kg has a ball of diameter d = 10.00 cm and mass M = 2.00 kg attached to one end. The arrangement is originally vertical and stationary, with the ball at the top as shown in the figure below. The combination is free to pivot about the bottom end of the rod after being given a slight nudge. (a) After the combination rotates through 90...
A uniform rod of mass 3.40×10−2 kg and length 0.410 m rotates in a horizontal plane...
A uniform rod of mass 3.40×10−2 kg and length 0.410 m rotates in a horizontal plane about a fixed axis through its center and perpendicular to the rod. Two small rings, each with mass 0.190 kg , are mounted so that they can slide along the rod. They are initially held by catches at positions a distance 5.50×10−2 m on each side from the center of the rod, and the system is rotating at an angular velocity 28.0 rev/min ....
A rod of length l=1.1m and mass M= 5.5kg joins two particles with masses m1 =4.8kg...
A rod of length l=1.1m and mass M= 5.5kg joins two particles with masses m1 =4.8kg and m2 = 2.8kg, at its ends. The combination rotates in the xy-plane about a pivot through the center of the rod with the linear speed of the masses of v= 3.5 m/s. (Moment of inertia of a uniform rod rotating about its center of mass I= 1 12 M l2 ) angularmomentum a) Calculate the total moment of inertia of the system I...
A rod of length l=2.2m and mass M= 9.7kg joins two particles with masses m1 =12.9kg...
A rod of length l=2.2m and mass M= 9.7kg joins two particles with masses m1 =12.9kg and m2 = 5.0kg, at its ends. The combination rotates in the xy-plane about a pivot through the center of the rod with the linear speed of the masses of v= 12.9 m/s. (Moment of inertia of a uniform rod rotating about its center of mass I= 1 12 M l2 ) a) Calculate the total moment of inertia of the system I =...
A meterstick (L = 1 m) has a mass of m = 0.134 kg. Initially, it...
A meterstick (L = 1 m) has a mass of m = 0.134 kg. Initially, it hangs from two short strings: one at the 25 cm mark and one at the 75 cm mark. 1) What is the tension in the left string? N 2) Now the right string is cut! What is the initial angular acceleration of the meterstick about its pivot point? (You may assume the rod pivots about the left string, and the string remains vertical) rad/s^2...