Question

a pipe 50mm in diameter is 6.5m long and the velocity in this pipe is 2.2m/s....

a pipe 50mm in diameter is 6.5m long and the velocity in this pipe is 2.2m/s. if the central 2m of this pipe is replaced by a pipe 75mm diameter, how much head loss would be saved. consider minor losses to be negligible and assume friction factor for a pvc pipe appropriately.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1- Water flows in a 10 m long and 4 cm diameter pipe contains 4 elbows...
1- Water flows in a 10 m long and 4 cm diameter pipe contains 4 elbows ( KL= 0.2 ) at velocity 8 m/s. Calculate the total head losses when the friction factor f=0.03 35.56 m 22.07 m 27.07 m 15.46 m 2- water flows in a 10 m long and 5 cm diameter horizontal pipe at rate 15 l/s Calculate the pressure drop Take the density of water 1000 kg/m3 and the dynamic viscosity 0.001 kg/m.s 74.13 kPa 96.41...
Water flows between two reservoirs through 800 ft of 12-inch diameter welded-steel pipe. The water surface...
Water flows between two reservoirs through 800 ft of 12-inch diameter welded-steel pipe. The water surface elevation difference between the two reservoirs is 16 ft. Find the flowrate (a) assuming head loss is only due to pipe friction, and (b) Accounting for both friction losses and minor losses due to a flush square-edged pipe entrance, the pipe exit, and a half-open gate valve in the line. Assume the water temperature is 60°F
Water flows between two reservoirs through 800 ft of 12-inch diameter welded-steel pipe. The water surface...
Water flows between two reservoirs through 800 ft of 12-inch diameter welded-steel pipe. The water surface elevation difference between the two reservoirs is 16 ft. Find the flowrate: (a) assuming head loss is only due to pipe friction, and (b) accounting for both friction losses and minor losses due to a flush square-edged pipe entrance, the pipe exit, and a half-open gate valve in the line. Assume the water temperature is 60°F.
The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the...
The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head through an abrupt contraction to 50 mm diameter. If the pressure in the 150 mm pipe is 345 kPa, what is the pressure in the 50 mm pipe, neglecting pipe friction?
Water flows through a pipe of 5mm in diameter with a mean velocity of 0.2 m/s....
Water flows through a pipe of 5mm in diameter with a mean velocity of 0.2 m/s. The dynamic viscosity of the water is given as 10-3 Pa s. Establish whether the equation f = 64/Re may be used to calculate the friction factor for this flow.
Provide an estimate of the interior diameter and the velocity of flow in a new ductile...
Provide an estimate of the interior diameter and the velocity of flow in a new ductile iron pipe bitumen lined used to transport raw water to a treatment plant. It is estimated that the head loss due to friction in the pipe is 0.35%. The measured pressurized flow rate in the pipe is 250l/s.
A smooth pipe 30 cm in diameter and 100 m long has a flush entrance and...
A smooth pipe 30 cm in diameter and 100 m long has a flush entrance and a submerged discharge. The velocity is 3 m/s. If the flowing water has a kinematic viscosity of v=1.16x10^-6 m² /s, What is the total head loss, hL?
SAE 30 Oil at 60oF flows through a 1.5 m diameter pipe at a velocity of...
SAE 30 Oil at 60oF flows through a 1.5 m diameter pipe at a velocity of 2.5 m/s. (3 points) What type of flow is occurring in the pipe:                 (2 points) If the pipe is made out of cast iron, determine the friction factor for flow through this pipe.
A centrifugal pump with a 10 cm suction pipe and a 7.5 cm diameter discharge pipe...
A centrifugal pump with a 10 cm suction pipe and a 7.5 cm diameter discharge pipe has a measured capacity of 0.019 m3/s (water), a suction side vacuum of 20 cm mercury (relative density = 13.6) and a discharge pressure of 240345 N/m2 (gage).  The suction and discharge pipes are at the same elevation.  Assuming that the head loss due to friction is negligible, what is the pump power required
A 250 mm diameter of cast iron pipe flows 39.3 L/s of SAE 10 oil along...
A 250 mm diameter of cast iron pipe flows 39.3 L/s of SAE 10 oil along 500 m length. Given: dynamic viscosity, μ and density, ρ of SAE 10 oil are 1.04 x 10-1 Ns/m2 and 917 kg/m3 respectively. By assuming the flow is laminar, determine energy head and pressure loss due to pipe friction using Hagen-Poiseuille equation and friction factor, f.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT