Question

The area of the piston to the master cylinder in a hydraulic braking system of a...

The area of the piston to the master cylinder in a hydraulic braking system of a 4-wheel car is 0.5 square inches. If a force of 5.2 lb is applied to this piston, what is the force on the brake pad of one wheel if the area of the pad is 2 square inches?

Homework Answers

Answer #1

In a hydraulic system, pressure change is transmitted to all the points equally. (Pascal's law)

At the master cylinder, pressure change is

At the brake pad, pressure change is

Force on the brake pad

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. A closed cylinder with a piston area of 2.33 square inches supports a load of...
1. A closed cylinder with a piston area of 2.33 square inches supports a load of 8,106.88 lb. What is the pressure (in psi) in the cylinder? 2. Find the force output (in lbs) of a cylinder that has a 2 square inch piston and a pressure of 2,714 psi. 3. An automobile weighing 1,707lbs is lifted by a lift that has a 3 in. diameter piston. What pressure (in psi) is required? 4. How much work is required to...
What force (in N) must be exerted on the master cylinder of a hydraulic lift to...
What force (in N) must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2200 kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.50 cm diameter, while the slave has a 24.0 cm diameter.
A hydraulic jack has an input piston of area 0.0520 m2 and an output piston of...
A hydraulic jack has an input piston of area 0.0520 m2 and an output piston of area 0.740 m2. How much force (in N) on the input piston is required to lift a car weighing 1.70 ✕ 104 N? ? = N
In a hydraulic press, the large piston of cross-sectional area A1 = 200 cm2 and the...
In a hydraulic press, the large piston of cross-sectional area A1 = 200 cm2 and the small piston has the cross-sectional area A2 = 5 cm2. If a force of 250 N is applied to the small piston, what is the magnitude of force F on the large piston? a. 10 N b. 1000 dyn c. 1000 N d. 10 kN
The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70...
The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70 cm2, and its large piston has a cross-sectional area of 199 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 14.0 kN?
A gas contained in a vertical piston–cylinder assembly by a piston with a face area of...
A gas contained in a vertical piston–cylinder assembly by a piston with a face area of 40 in2 and weight of 100 lbf. The atmosphere exerts a pressure of 14.7 lbf/in2 on top of the piston. A paddle wheel transfers 3 Btu of energy to the gas during a process in which the elevation of the piston increases slowly by 4 ft. The piston and cylinder are poor thermal conductors, and friction between the piston and cylinder can be neglected....
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston...
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston supporting the car is A, the area of the other piston is a, and the ratio A/a is 101.7. How far must the small piston be pushed down to raise the car a distance of 1.2 cm 2.The pressure inside a bottle of champagne is 4.8 atm higher than the air pressure outside. The neck of the bottle has an inner radius of 0.9...
2.A hydraulic car lift has an input piston of radius 6.20 cm and negligible weight. The...
2.A hydraulic car lift has an input piston of radius 6.20 cm and negligible weight. The output piston has a radius of 86.9cm. If the total load on the output plungers needs to be 12,000 N. What is the mechanical advantage of the hydraulic system input? 3. A hydraulic car lift has an input piston of radius 4.80 cm and negligible weight. The output piston has a radius of 101 cm. If the total load on the output plungers needs...
A linear actuator such as you used in lab has a rod of area of 10-4...
A linear actuator such as you used in lab has a rod of area of 10-4 m2 and a piston area of 3*10-4 m2 . The actuator can have fluid applied to either the piston end of the cylinder or the open end where the rod comes out so the rod can both extend and retract out of the cylinder. A student establishes equilibrium between the hydraulic force and an external weight so there is no movement of the weight....
A piston cylinder system contains 2 kg of R-134a under conditions of 100 kPa and 0.5...
A piston cylinder system contains 2 kg of R-134a under conditions of 100 kPa and 0.5 dryness. Heat is supplied to the system from a 500 K source. If the exergy destroyed is 20 kJ, the final situation what? Environmental temperature 300 K.