Question

Consider the hydraulic car lift. True or False: When the car is pushed up, the work...

Consider the hydraulic car lift. True or False: When the car is pushed up, the work done by the large piston is greater than the work done by the small one?

Homework Answers

Answer #1

(1) In hydraulic lifting work done is same for both the pistons. Thus, given statement is false.

Reason:

since pressure is same for both the pistion;

where A1 and A2 are the area of cross section of piston;

these areas are inversely proportional to the displacement of piston as;

compare equation (1) and (2)

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston...
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston supporting the car is A, the area of the other piston is a, and the ratio A/a is 101.7. How far must the small piston be pushed down to raise the car a distance of 1.2 cm 2.The pressure inside a bottle of champagne is 4.8 atm higher than the air pressure outside. The neck of the bottle has an inner radius of 0.9...
A hydraulic jack is designed to lift a car by exerting an output force 100 times...
A hydraulic jack is designed to lift a car by exerting an output force 100 times as large as the input (see class notes). (a) What must be the ratio of the cylinder diameter on the output side to that on the input side? (b) If the input side is pushed down by 10 cm, how much does the output side move up? (The fluid volume lost on the input side is gained on the output side.) (c) Show that...
A car lift in a garage uses incompressible oil. A small input piston of radius 4.00...
A car lift in a garage uses incompressible oil. A small input piston of radius 4.00 cm is connected to a large piston of radius 16.00 cm via a sealed chamber. The large piston is connected to a platform on which rests a car. The combined mass of the platform and car is 1500 kg. (a) What is the minimum force required at the input piston to begin to raise the car? (b)What pressure is exerted at the small piston...
A hydraulic jack used to lift cars is called a three-ton jack. The large piston is...
A hydraulic jack used to lift cars is called a three-ton jack. The large piston is 22 mm in diameter, the small one 6.3 mm. Assume that a force of 3 tons is 3.0 x 104 N. a. What force must be exerted on the small piston to lift the 3-ton weight? b. Most jacks use a lever to reduce the force needed on the small piston. If the resistance arm is 3.0 cm, how long is the effort arm...
The hydraulic oil in a car lift has a density of 8.73 x 102 kg/m3. The...
The hydraulic oil in a car lift has a density of 8.73 x 102 kg/m3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 8.10 x 10-3 m and 0.101 m, respectively. What input force F is needed to support the 24000-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface...
The hydraulic oil in a car lift has a density of 8.04 x 102 kg/m3. The...
The hydraulic oil in a car lift has a density of 8.04 x 102 kg/m3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 7.63 x 10-3 m and 0.158 m, respectively. What input force F is needed to support the 26400-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface...
A 1225-kg car is raised using a hydraulic lift, which consists of a U-tube with arms...
A 1225-kg car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with oil with a density of 800. kg/m3 and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 18.0 cm and the narrower arm has a radius of 5.00 cm. The car rests on the piston on the wider arm of the U-tube. The wider piston is raised to a position that...
A hydraulic lift has 2 connected pistons with cross-sectional areas 20 cm2 and 680 cm2. It...
A hydraulic lift has 2 connected pistons with cross-sectional areas 20 cm2 and 680 cm2. It is filled with oil of density 710 kg/m3. What mass must be placed on the small piston to support a car of mass 1400 kg at equal fluid levels? m = With the lift in balance with equal fluid levels, a person of mass 90 kg gets into the car. What is the equilibrium height difference in the fluid levels in the pistons? Δh...
A) A 1500-kg car is lifted to a height h by a hydraulic lift containing an...
A) A 1500-kg car is lifted to a height h by a hydraulic lift containing an incompressible fluid. A force of F_1 applied on a piston of area A_1 results in a larger force of F_2 on the plunger of larger area A_2. Suppose the piston has a radius of 0.0120 m and the plunger’s radius is 0.150 m. Calculate the height to which the car is lifted if the work done by the plunger is 200 J. (Assume that...
(a) (2 marks) A 2000-kg car is lifted to a height h by a hydraulic lift...
(a) A 2000-kg car is lifted to a height h by a hydraulic lift containing an incompressible fluid. A force of F1 applied on a piston of area A1 results in a larger force of F2 on the plunger of larger area A2 . Suppose the piston has a radius of 0.0120 m and the plunger’s radius is 0.750 m. Calculate the height to which the car is lifted if the work done by the plunger is 200 J. (Assume...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT