Question

A hydraulic jack has an input piston of area 0.0520 m2 and an output piston of...

A hydraulic jack has an input piston of area 0.0520 m2 and an output piston of area 0.740 m2. How much force (in N) on the input piston is required to lift a car weighing 1.70 ✕ 104 N?

? = N

Homework Answers

Answer #1

Given:

Input piston area,

Output piston area,

Weight of the car,

------------

A hydraulic jack works according to the Pascal's law.

Pascal's Law states that the pressure change in a confined incompressible fluid is transmitted equally throughout the fluid.

So pressure at input piston is equal to pressure at output piston

Pressure = Force/Area

Force at output piston is the weight of the car

ANSWER:

==========================

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
2.A hydraulic car lift has an input piston of radius 6.20 cm and negligible weight. The...
2.A hydraulic car lift has an input piston of radius 6.20 cm and negligible weight. The output piston has a radius of 86.9cm. If the total load on the output plungers needs to be 12,000 N. What is the mechanical advantage of the hydraulic system input? 3. A hydraulic car lift has an input piston of radius 4.80 cm and negligible weight. The output piston has a radius of 101 cm. If the total load on the output plungers needs...
The fine piston of a hydraulic jack has a diameter of 1.30 cm. With an applied...
The fine piston of a hydraulic jack has a diameter of 1.30 cm. With an applied force of only 23 N it was possible to lift a weight of 1850 N. Assuming that both pistons are circular, what is the diameter of the wide working piston for this hydraulic jack?
A hydraulic jack used to lift cars is called a three-ton jack. The large piston is...
A hydraulic jack used to lift cars is called a three-ton jack. The large piston is 22 mm in diameter, the small one 6.3 mm. Assume that a force of 3 tons is 3.0 x 104 N. a. What force must be exerted on the small piston to lift the 3-ton weight? b. Most jacks use a lever to reduce the force needed on the small piston. If the resistance arm is 3.0 cm, how long is the effort arm...
1. A closed cylinder with a piston area of 2.33 square inches supports a load of...
1. A closed cylinder with a piston area of 2.33 square inches supports a load of 8,106.88 lb. What is the pressure (in psi) in the cylinder? 2. Find the force output (in lbs) of a cylinder that has a 2 square inch piston and a pressure of 2,714 psi. 3. An automobile weighing 1,707lbs is lifted by a lift that has a 3 in. diameter piston. What pressure (in psi) is required? 4. How much work is required to...
A hydraulic jack is designed to lift a car by exerting an output force 100 times...
A hydraulic jack is designed to lift a car by exerting an output force 100 times as large as the input (see class notes). (a) What must be the ratio of the cylinder diameter on the output side to that on the input side? (b) If the input side is pushed down by 10 cm, how much does the output side move up? (The fluid volume lost on the input side is gained on the output side.) (c) Show that...
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston...
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston supporting the car is A, the area of the other piston is a, and the ratio A/a is 101.7. How far must the small piston be pushed down to raise the car a distance of 1.2 cm 2.The pressure inside a bottle of champagne is 4.8 atm higher than the air pressure outside. The neck of the bottle has an inner radius of 0.9...
The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70...
The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70 cm2, and its large piston has a cross-sectional area of 199 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 14.0 kN?
The hydraulic oil in a car lift has a density of 8.73 x 102 kg/m3. The...
The hydraulic oil in a car lift has a density of 8.73 x 102 kg/m3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 8.10 x 10-3 m and 0.101 m, respectively. What input force F is needed to support the 24000-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface...
The hydraulic oil in a car lift has a density of 8.04 x 102 kg/m3. The...
The hydraulic oil in a car lift has a density of 8.04 x 102 kg/m3. The weight of the input piston is negligible. The radii of the input piston and output plunger are 7.63 x 10-3 m and 0.158 m, respectively. What input force F is needed to support the 26400-N combined weight of a car and the output plunger, when (a) the bottom surfaces of the piston and plunger are at the same level, and (b) the bottom surface...
A hydraulic lift has pistons with diameters 8.00 cm and 36.0 cm, respectively. If a force...
A hydraulic lift has pistons with diameters 8.00 cm and 36.0 cm, respectively. If a force of 825 N is exerted at the input piston, what maximum mass can be lifted by the output piston?